Pixsys ATR 142 Скачать руководство пользователя страница 42

Страница: 42 / 58

42 - ATR142 -

User manual

a.1.de.

Alarm 1 Delay

-180…+180

Sec. >

Default

: 0.

Negative: delay at exit from alarm

Positive: delay at starting of alarm

a.1.s.p.

Alarm 1 Setpoint Protection

does not allow the user to modify setpoint.

Free

Default

Lock.

Locked

Hide

Locked and hidden

aL. 2

Alarm 2

Alarm 2 selection. Alarm intervention is associated to AL2.

dis.

Disabled >

Default

a. aL.

Absolute Alarm

b. aL.

Band Alarm

H.d.aL.

High Deviation Alarm

L.d.aL.

Low Deviation Alarm

a.c.aL.

Absolute Command setpoint Alarm

st.aL.

Start Alarm, Attivo in Run

CooL

Cooling

t.1.s.a.

Timer 1 Start Alarm

t.1.e.a.

Timer 1 End Alarm

t.1.w.e.

Timer 1 Warning Expiring

t.2.s.a.

Timer 2 Start Alarm

t.2.e.a.

Timer 2 End Alarm

t.2.w.e.

Timer 2 Warning Expiring

t.1.2.s.

Timer 1-2 Start Alarm

t.1.2.e.

Timer 1-2 End Alarm

t.1.2.w.

Timer 1-2 Warning Expiring

Содержание ATR 142



























































Результаты поиска

Содержание ATR 142

Отзывы:

Похожие инструкции для ATR 142

Бренды по названию

Популярные бренды

Pixsys ATR 142, Руководство пользователя

Результаты поиска

Содержание ATR 142

Отзывы:

Похожие инструкции для ATR 142

Бренды по названию

Популярные бренды