Pixsys ATR 142 Скачать руководство пользователя страница 17

Страница: 17 / 58

User manual -

ATR142- 17

Automatic/manual tuning cannot be enabled if the Soft start

is active.

8.6 Automatic / manual regulation for %

output control

This function allows to select automatic functioning or

manual command of the output percentage.

Parameter 49

Au.ma.

, can select two methods.

• First selection

en.

: pressing the

FNC

key display 1 shows

p.---

, while display 2 shows

Auto

Press the “

” key to select

man.

mode; it is now possible,

to change the output percentage using the keys “

”

and “

”. To return to automatic mode, using the same

procedure, select

auto

on display 2:

led switches off

and functioning returns to automatic mode.

• Second selection

en.st.

: same functioning, but with two

important variants:

- If there is a temporary power failure or after switch-off,

manual functioning as well as the previous output

percentage value will be maintained at restarting.

- If the sensor breaks during automatic functioning,

controller moves to manual mode while maintaining the

output percentage command unchanged as generated by

the PID immediately before breakage.

8.7 Pre-Programmed cycle

Pre-programmed cycle function activates by setting

pr.cY.

parameter 48

op.Mo.

Controller reaches setpoint1 basing on the gradient set

on parameter 51

Grad.

, then it reaches max. power up

to setpoint2. When the process reaches max. power, this

setpoint is maintained for the time set on parameter 52

ma.t.i.

At expiry, process will reach ambient temperature according

to gradient entered on parameter 64

fa.Gr.

, then command

output will be disabled and display will visualize

Stop

Содержание ATR 142



























































Результаты поиска

Содержание ATR 142

Отзывы:

Бренды по названию

Популярные бренды

Pixsys ATR 142, Руководство пользователя

Результаты поиска

Содержание ATR 142

Отзывы:

Бренды по названию

Популярные бренды