Pixsys ATR 142 Скачать руководство пользователя страница 40

Страница: 40 / 58

40 - ATR142 -

User manual

t.c.

Cycle Time

Cycle time for time-proportioning output (10/15sec for

PID contactors, 1 sec for PID on SSR or value declared by

manufacturer for motorised valves)

0.1-300.0

sec. >

Default

: 10.0.

For motorised valve min. time is 1.0 sec

o.po.L.

Output Power Limit

limit of output power %.

10-100

% >

Default

: 100

aL. 1

Alarm

operating mode for Alarm 1. Intervention of the alarm is

associated to AL1.

dis.

Disabled >

Default

a. aL.

Absolute Alarm (parameter 12)

b. aL.

Band Alarm (parameter 12)

H.d.aL.

High Deviation Alarm (parameter 12)

L.d.aL.

Low Deviation Alarm (parameter 12)

a.c.aL.

Absolute Command setpoint Alarm

st.aL.

Start Alarm, Active in Run

cooL.

Cooling

t.1.s.a.

Timer 1 Start Alarm

t.1.e.a.

Timer 1 End Alarm

t.1.w.e.

Timer 1 Warning Expiring

t.2.s.a.

Timer 2 Start Alarm

t.2.e.a.

Timer 2 End Alarm

t.2.w.e.

Timer 2 Warning Expiring

t.1.2.s.

Timer 1-2 Start Alarm

t.1.2.e.

Timer 1-2 End Alarm

t.1.2.w.

Timer 1-2 Warning Expiring

Содержание ATR 142



























































Результаты поиска

Содержание ATR 142

Отзывы:

Похожие инструкции для ATR 142

Бренды по названию

Популярные бренды

Pixsys ATR 142, Руководство пользователя

Результаты поиска

Содержание ATR 142

Отзывы:

Похожие инструкции для ATR 142

Бренды по названию

Популярные бренды