Pixsys ATR 142 Скачать руководство пользователя страница 47

Страница: 47 / 58

User manual -

ATR142- 47

dGt.i.

Digital Input

Digital input functioning. (parameter 7.11)

Parameter 48 selection must be

cont.

Pr.cy.

dis.

Disabled >

Default

st.st.

Start/Stop

rn.n.o.

Run n.o.

rn.n.c.

Run n.c.

L.c.n.o.

Lock Conversion n.o. (Lock visualisation on

display with N.O. contact)

L.c.n.c.

Lock Conversion n.c. (Lock visualisation on

display with N.C. contact)

tune

Tune > Manual

a.ma.i.

Automatic Manual impulse

a.ma.c.

Automatic Manual Contact

t.1.s.s.

Timer 1 Start Stop

Grad.

Gradient

Rising gradient for soft start or pre-programmed cycle

Disabled >

Default

: 0.

1-9999

Digit/time

(degrees/hours with display of tenths

if temperature)

ma.ti.

Maintenance Time

maintenance time for pre-programmed cycle

00.00-24.00

hh.mm >

Default

: 00.00

The display of decimal point depends on the setting of parameter

sen.

and the parameter

d.p.

Содержание ATR 142



























































Результаты поиска

Содержание ATR 142

Отзывы:

Бренды по названию

Популярные бренды

Pixsys ATR 142, Руководство пользователя

Результаты поиска

Содержание ATR 142

Отзывы:

Бренды по названию

Популярные бренды