Pixsys ATR 142 Скачать руководство пользователя страница 22

Страница: 22 / 58

22 - ATR142 -

User manual

8.12 Dual action heating-cooling

ATR142 is suitable also for systems requiring a combined

heating-cooling action.

Main command output must be configured foe hearting PID

(

act.t.

Heat

and

p.b.

must be greater than 0), and one of the

alarms (

AL.1

AL. 2

) must be configured as

cooL.

Command

output must be connected to the actuator responsible for

heat, while the alarm output will control cooling action.

Parameters to configure for the Heating PID are:

act.t.

Heat

Command output type (Heating)

p.b.

: Heating proportional band

t.i.

: Integral time of heating and cooling

t.d.

: Derivative time of heating and cooling

t.c.

: Heating time cycle

The parameters to configure for the Cooling PID are the

following (example: action associated to alarm1):

AL. 1

cooL

Alarm1 selection (cooling)

p.b.m.

: Proportional band multiplier

ou.d.b.

: Overlapping/Dead band

co.t.c.

: Cooling time cycle

Parameter

p.b.m.

(that ranges from 1.00 to 5.00) determines

the proportional band of cooling basing on the formula:

Cooling proportional band

p.b.

p.b.m.

This gives a proportional band for cooling which will be the

same as heating band if

p.b.m.

= 1.00, or 5 times greater if

p.b.m.

= 5.00. The

integral time and derivative time

are the

same for both actions.

Parameter

ou.d.b.

determines the overlapping percentage

between the two actions. For systems in which the heating

and cooling output must never be simultaneously active a

dead band (

ou.d.b.

≤ 0) can be configured, and viceversa an

overlapping (

ou.d.b.

> 0).

The following diagram shows an example of dual PID action

(heating-cooling) with

t.i.

= 0 and

t.d.

= 0.

Содержание ATR 142



























































Результаты поиска

Содержание ATR 142

Отзывы:

Похожие инструкции для ATR 142

Бренды по названию

Популярные бренды

Pixsys ATR 142, Руководство пользователя

Результаты поиска

Содержание ATR 142

Отзывы:

Похожие инструкции для ATR 142

Бренды по названию

Популярные бренды