Pit Boss Mile Hybrid Скачать руководство пользователя

Страница: 30 / 42

TROUBLESHOOTING

Proper cleaning, maintenance and the use of clean, dry, quality fuel will prevent common operational problems. When your Pit

Boss® grill is operating poorly, or on a less frequent basis, the following troubleshooting tips may be helpful. For FAQ, please visit

www.pitboss-grills.com

. You may also contact your local Pit Boss® authorized dealer or contact Customer Care for assistance.

WARNING: Always disconnect the electrical cord prior to opening the grill for any inspection, cleaning,

maintenance or service work. Ensure the grill is completely cooled to avoid injury.

WOOD PELLET GRILL

PROBLEM

CAUSE

SOLUTION

No Power Lights On

The Control Board

Not Connected To Power

Source

Ensure unit is plugged into a working power source. Reset breaker. Ensure GFCI is a minimum 15 Amp

service (see

Electric Wire Diagram

for access to electric components) Ensure all wire connections are

firmly connected and dry.

Fuse Blown On The

Control Board

Remove hopper access panel (see

Electric Wire Diagram

for diagram), press in plastic tabs holding

the control board in place and carefully pull controller inside the hopper to release controller. Check

the fuse for a broken wire or if the wire has turned black. If yes, fuse needs to be manually replaced.

The GFCI outlet has

been tripped.

Remove hopper access panel (see

Electric Wire Diagram

for diagram), and ensure all wire connections

are firmly connected and dry. Ensure GFCI is a minimum 15 Amp service.

Faulty Control Board

Control Board needs to be replaced. Contact Customer Care for a replacement part.

Fire in Burn Pot Will

Not Light

Auger Not Primed

Before the unit is used for the first time or anytime the hopper is completely emptied out, the auger

must be primed to allow pellets to fill the auger tube. If not primed, the igniter will timeout before

the pellets reach the Burn Pot. Follow

Hopper Priming Procedure

Auger Motor Is Jammed Remove cooking components from the Main Barrel. Press the Power Button to turn the unit on, turn

Temperature Control Dial to SMOKE, and inspect the auger feed system. Visually confirm that the

auger is dropping pellets into the Burn Pot. If not operating properly, call Customer Care for assistance

or a replacement part.

Igniter Failure

Remove cooking components from the Main Barrel. Press the Power Button to turn the unit on,

turn Temperature Control Dial to SMOKE, and inspect the igniter. Visually confirm that the igniter

is working by placing your hand above the Burn Pot and feeling for heat. Visually confirm that the

igniter is protruding approximately 13mm / 0.5 inches in the Burn Pot. If not operating properly, follow

Manual Start-up Procedure

to continue use of grill; however, call Customer Care for assistance or a

replacement part.

Flashing Dots On LCD

Screen

The Igniter Is On

This is not an error that effects the grill. Used to show that the unit has power and is in Start-Up mode

(igniter is on). The igniter will turn off after five minutes. Once the flashing dots disappear, the grill

will begin to adjust to the desired temperature selected.

Flashing Temperature

On LCD Screen

Grill Temperature Is

Below 65°C /150°F

This is not an error that effects the unit; however, it is used to show that there is some risk that the

fire could go out. Check hopper for sufficient fuel or if there is an obstruction in the feed system.

Remove pellets and follow

Care and Maintenance

instructions. Check grill Grill Probe and follow

Care

and Maintenance

instructions if dirty. Check Burn Pot for ash build-up or obstructions, and follow

Care and Maintenance

instructions for ash build-up. Check fan. Ensure it is working properly and

air intake is not blocked. Follow

Care and Maintenance

instructions if dirty. Check auger motor to

confirm operation (rotation), and ensure there is no blockage in the auger tube.

Содержание Mile Hybrid











































Результаты поиска

Содержание Mile Hybrid

Отзывы:

Похожие инструкции для Mile Hybrid

Бренды по названию

Популярные бренды

Pit Boss Mile Hybrid, Сборка и эксплуатация

Результаты поиска

Содержание Mile Hybrid

Отзывы:

Похожие инструкции для Mile Hybrid

Бренды по названию

Популярные бренды