Pit Boss Mile Hybrid Скачать руководство пользователя | Manualshive

Страница: 19 / 42

background image

19

MANUAL LIGHTING PROCEDURE

1.  Open lid during lighting.
2.  Set all Control Knobs to the “Off” position.
3.  Open the cylinder/gas valve according to the operating

instructions on tank.

4. Quickly and carefully, using a long match or long-nosed

lighter, place a lit flame near the burner and watch the burner

catch flame. Gain access to the burner from beneath the

Cooking Grids and Heat Tents. Position lit match near the side

of the burner.

CAUTION: Do not attempt to light another area of the

burner. This can cause injury.

5. If the burner does not light within 5 seconds, turn burner

Control Knob to “Off”, wait 5 minutes, and repeat lighting

instruction. After lighting, observe the burner flame. Make

sure all burner ports are lit and flame height matches

illustration shown previously.

NOTE: Each burner lights independently - repeat same steps for other burner.

WARNING: Never lean over the cooking area while lighting your gas grill. Keep your face and body a safe

distance (at least 457 mm / 18 inches) from the cooking grid surface when lighting your grill by match.

6. If the above points do not work, see

Troubleshooting.

SHUTTING OFF YOUR GRILL

1. When finished cooking, turn gas cylinder valve to the CLOSED position, and allow the regulator knob to pop out. This safety

feature locks the regulator knob to ensure that the gas is no longer flowing.

2. Turn Control Knobs to the “Off” position.

NOTE: A “poof” sound is normal as the last of the LP gas is burned.

3. Disconnect gas supply by following the

Disconnecting A Gas Cylinder

instructions.

WARNING: Allow the grill to cool completely, and remove the gas cylinder, before moving, travel, or for

storage.

«
...
17
18
19
20
21
...
»

Содержание Mile Hybrid











































Отзывы:

Нет отзывов

Похожие инструкции для Mile Hybrid

Бренд: Landmann Страницы: 8

Бренд: Dacor Страницы: 4

450 Series K450GB

Бренд: Kalamazoo Страницы: 11

Бренд: Livoo Страницы: 8

Бренд: Nexgrill Страницы: 49

Бренд: Draper Страницы: 12

Бренд: Luna Страницы: 149

Бренд: Outback Страницы: 19

Бренд: Better Homes and Gardens Страницы: 10

Бренд: Clatronic Страницы: 62

Бренд: BlackFlame Страницы: 22

Бренд: stayer Страницы: 28

Бренд: Z GRILLS Страницы: 26

GALAXY BQ1190BLB

Бренд: Gasmate Страницы: 24

Бренд: garbou Страницы: 24

Бренд: 3 Embers Страницы: 45

Бренд: Ford Страницы: 13

Бренд: Klarstein Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды