Pit Boss Mile Hybrid Скачать руководство пользователя

Страница: 11 / 42

8. SECURING THE LID STOPPER

Parts Required:

1 x Lid Stopper (#3)

Installation:

• Secure the Lid Stopper onto the top of the Main Barrel using the

pre-installed hardware on top of the Main Barrel.

9. MOUNTING THE HOPPER HANDLE

Parts Required:

1 x Hopper Handle (#9)

4 x Screw (#C)

Installation:

• Secure the Hopper Handle onto the left side of the Hopper using the

four screws.

10. INSTALLING THE FLAME COMPONENTS

Parts Required:

1 x Flame Broiler Main Plate (#5)

2 x Heat Tents (#6)

1 x Flame Baffle (#7)

Installation:

• Place the Flame Baffle over the Burn Pot, located in the bottom of the

Main Barrel. Note illustration 10A.

NOTE: The side of the Flame Baffle with the shortest edge should

be facing the hopper. Poor installation of this part may result in

damage to your Main Barrel.

• Insert the Flame Broiler Main Plate into the Main Barrel, right side

first. Rest the Flame Broiler Main Plate on the built-in ledge (on the

inside right) of the Main Barrel that directs grease towards the grease

bucket. Slide the entire piece to the left side, and the two slots on the

Flame Broiler Main Plate will fit into the rounded ledge above the Burn

Pot. It will sit slightly at a downward angle. Note illustration 10B.

IMPORTANT: If the Flame Broiler Main Plate is on the base of the

barrel, it is installed incorrectly. The Flame Broiler Main Plate should

sit at an angle, with the left side sitting higher than the right. Poor

installation of this part may result in damage to your Main Barrel.

• Next, install the two Heat Tents into the notches directly over the

openings of the Flame Broiler Main Plate. Note illustrations 10C and

10D for proper positioning.

10A

10B

10C

10D

Содержание Mile Hybrid











































Результаты поиска

Содержание Mile Hybrid

Отзывы:

Похожие инструкции для Mile Hybrid

Бренды по названию

Популярные бренды

Pit Boss Mile Hybrid, Сборка и эксплуатация

Результаты поиска

Содержание Mile Hybrid

Отзывы:

Похожие инструкции для Mile Hybrid

Бренды по названию

Популярные бренды