Pit Boss Mile Hybrid Скачать руководство пользователя

Страница: 32 / 42

PROPANE GAS GRILL

PROBLEM

CAUSE

SOLUTION

Grill Will Not Light

The ignition wire came

off the electrical igniter/

valve.

Reconnect the ignition wire to the electrical igniter/valve.

The ignition wire is

broken

Contact Customer Service for assistance or a replacement part.

The battery has died

Install a new battery.

New battery doesn’t

work

Check the battery polarity. The negative (-) side of the battery goes in first.

The electrode tip does

not produce sparks at

the burner port

Adjust the electrode.

No gas supplied

Check the regulator valve. Check connection for leak.

Excessive Flare-Up

Grilling fatty meats

Grill fatty meats when the grids are cold, and the knobs are on the “LOW” setting. Move the meats to

the warming rack if flare-up continues.

Cooking temperature

Attempt cooking at a lower temperature. Grease does have a flash point. Keep the temperature under

176°C / 350°F when cooking highly greasy food.

Water sprayed on gas

flames

Do not spray water on gas flames.

Burner Blows Out

Gas tank is empty

Refill the gas tank.

Burner is not aligned

with the control valve

Install the burner correctly.

Gas supply is not

sufficient

Check the gas supply hose and make sure there are no leaks and no knots.

Low Heat When On

“HIGH”

Ports are blocked

Clear ports of any obstructions.

Gas tank has run out

Refill the gas tank.

Содержание Mile Hybrid











































Результаты поиска

Содержание Mile Hybrid

Отзывы:

Похожие инструкции для Mile Hybrid

Бренды по названию

Популярные бренды

Pit Boss Mile Hybrid, Сборка и эксплуатация

Результаты поиска

Содержание Mile Hybrid

Отзывы:

Похожие инструкции для Mile Hybrid

Бренды по названию

Популярные бренды