background image

7

PARTS & SPECS

Part#

Description

1

Porcelain-Coated Steel Upper Cooking Rack (x1)

2

Porcelain-Coated Steel Cooking Grids (x2)

3

Lid Stopper (x1)

4

Meat Probe (x1)

5

Flame Broiler Main Plate (x1)

6

Heat Tent (x2)

7

Flame Baffle (x1)

8

Thermometer (x1)

9

Hopper Handle (x1)

10

Control Knob (x2)

11

Main Barrel (x1)

12

Left Support Leg - Front (x1)

13

Left Support Leg - Back (x1)

14

Right Support Leg - Front (x1)

15

Right Support Leg - Back (x1)

16

Side Shelf (x1)

17

Gas Cylinder Wire Retainer (x1)

18

Gas Cylinder Support Panel (x1)

19

Grease Bucket (x1)

20

Cart Bar (x2)

21

Bottom Shelf (x1)

22

Wheels (x2)

A

Screw (x16)

B

Screw (x4)

C

Screw (x9)

D

R-Pin (x2)

E

Wheel Cotter Pin (x2)

F

Wheel Axle Pin (x2)

G

Wheel Washer (x2)

H

Regulator Hose Retainer (x1)

I

Battery (x1)

NOTE: Due to ongoing product development, parts are subject to change without notice. Contact 

Customer Service if parts are missing when assembling the unit.

PB – ELECTRIC REQUIREMENTS

110-120 V, 60 Hz, 250 W, 3-PRONG GROUNDED PLUG

4

5

1

2

3

6

7

8

10

11

12

13

14

15

16

17

18

19

20

21

22

A
B

C

D

G

E

H

F

I

MODEL

ASSEMBLED (WxDxH)

WEIGHT

COOKING AREA

BTU/HR

PB

PB600HY

1,261 X 701 X 1,149 MM

/ 49.6 X 27.6 X 45.2 IN.

51.0 KG  

/ 112.4 LB

MAIN - 2,828 CM² / 438.4 IN

2

UPPER - 1,118 CM² / 173.3 IN

2

 

TOTAL - 3,946 CM² / 611.7 IN

2

24,000

9

Содержание Mile Hybrid











































Отзывы: