Pioneer PDP-4270HD Скачать руководство пользователя страница 86

Страница: 86 / 208

PDP-4271HD

5.1.6 FLOWCHART OF FAILURE ANALYSIS FOR THE VIDEO SYSTEM

Flowchart of Failure Analysis for The Video System

Is the selected input signal a
composite signal?

Are the data displayed on the
"HDMI SIGNAL INFO" page of
the Factory menu correct?

The source equipment previously
used is in failure.
No problem with the MAIN Assy.

Is the sync signal output from
IC5401?

Does the result of SIG mode
detection on the Factory menu
coincide with the input signal data?

Is a video signal output from
IC5401?
(110 to 113, 116 to 119)
(123 to 126, 129 to 132)
(133, 136, 137, 140 to 144)

Info Frame data have not been acquired.

Check if Function corresponding to the input signal is selected.

Yes

After changing the source
equipment, check the "HDMI
SIGNAL INFO" data again.

Replace the MAIN Assy.

IC5401 and its peripheral circuits
are in failure.

Replace the MAIN Assy.

The input signal is not displayed.

⇒

COMP / S1

Is the selected input signal a
s-video signal?

Yes

⇒

COMP / S1

⇒

COMP / S2

Is the selected input signal a
PC signal?

Yes

⇒

COMP / PC2

Is the selected input signal a
analog component signal?

Is the selected input signal an
analog TV signal?

Yes

Is the selected input signal an
HDMI signal?

Yes

⇒

DTV

Is the selected input signal a
digital TV signal?

Yes

⇒

USB

Is the selected input signal a
USB signal?

No problem with the MAIN Assy

Yes

Is the sync signal input to IC8001?

The signal identification path is
in failure.

Replace the MAIN Assy.

IC8001 and its peripheral circuits are in failure.

Replace the MAIN Assy.

Yes

IC8001 and its peripheral circuits are in failure.

Replace the MAIN Assy.

Yes

⇒

COMP / PC1

Failure analysis for the
MAIN Assy.

⇒

MA3

Содержание PDP-4270HD

















































































































































































































Результаты поиска

Содержание PDP-4270HD

Отзывы:

Похожие инструкции для PDP-4270HD

Бренды по названию

Популярные бренды

Pioneer PDP-4270HD, Руководство по обслуживанию

Результаты поиска

Содержание PDP-4270HD

Отзывы:

Похожие инструкции для PDP-4270HD

Бренды по названию

Популярные бренды