Pioneer PDP-4270HD Скачать руководство пользователя страница 110

Страница: 110 / 208

PDP-4271HD

110

7. ADJUSTMENT

7.1 ADJUSTMENT REQUIRED WHEN THE SET IS REPAIRED OR
REPLACED

1. At shipment, the unit is adjusted to its best conditions. Normally, it is not necessary to readjust even if an assembly is replaced. If the

adjustment is shifted or if it becomes necessary to readjust because of part replacement, etc., perform the adjustment as described below.

2. Any value changed in Service/Factory mode will be stored in memory as soon as it is changed. Before readjustment, take note of the

original values for reference in case you need to restore the original settings.

3. Use a stable AC power supply.

42 Y DRIVE Assy

No adjustment required

TANSHI Assy

No adjustment required

POWER SUPPLY Unit

42 DIGITAL Assy

42 X DRIVE Assy

No adjustment required

Refer to "7.4 HOW TO CLEAR HISTORY DATA"
and "7.6 PROCEDURE WHEN REPLACING THE
POWER UNIT"

MAIN Assy (

∗

)

No adjustment required

Service Panel Assy

Refer to "7.5 ADJUSTMENTS WHEN THE SERVICE
PANEL ASSY IS REPLACED."

Writing of backup data is required.
Refer to the "7.3 BACKUP WHEN THE PANEL
UNIT IS ADJUSTED. "

SENSOR Assy

Writing of backup data is required.
Refer to the "7.3 BACKUP WHEN THE PANEL
UNIT IS ADJUSTED. "

When any of the following assemblies is replaced

Note: Checking the Cable Card ID

The PDP has a slot for a cable card that is used for managing your
information by the cable TV company. The following procedure
allows you to check your Cable Card ID and the Host ID.

Press HOME MENU.

Select “Tuner Setup”. ( / then ENTER)

Select “Channel Setup”. ( / then ENTER)

Select “POD ID”. ( / )
• The Host ID and Cable Card ID appear.

5. Press HOME MENU to exit the menu.

(

∗

) : When replacing the MAIN Assy, be sure to do the FINAL SETUP.

Содержание PDP-4270HD

















































































































































































































Результаты поиска

Содержание PDP-4270HD

Отзывы:

Похожие инструкции для PDP-4270HD

Бренды по названию

Популярные бренды

Pioneer PDP-4270HD, Руководство по обслуживанию

Результаты поиска

Содержание PDP-4270HD

Отзывы:

Похожие инструкции для PDP-4270HD

Бренды по названию

Популярные бренды