Pioneer PDP-4270HD Скачать руководство пользователя страница 169

Страница: 169 / 208

PDP-4271HD

169

9.3.15 SETTING FOR FACTORY MODE PERMISSION / PROHIBITION [FAY /FAN]

9.3.16

BACKUP FUNCTION FOR ADJUSTMENT VALUE FOR THE MAIN UNIT [FAJ /UAJ /CBU /

BCP]

The commands FAY/FAN are for prohibiting/permitting panel-adjustment commands.

Command

Format

Operation

Remarks

Effective Operation

Modes

Control

[FAY]

Normal operation mode
while the power is on

Adjust command is valid.

Mask indications will be forcibly turned off.

[FAN]

During FAY

Adjust command is invalid.

Command

Format

Operation

Remarks

Effective

Operation Modes

Control

[FAJ]

During FAY

To make the flag setting that
indicating that adjustment of the
panel unit has been completed

Writing 00 to the 4 k byte ROM and
copying to the 2 k byte ROM

This takes at least 350 ms.

[UAJ]

To make the flag setting that
indicating that adjustment of the
main unit has not been completed

Writing F0 to the 4 k byte ROM

[CBU]

To make the flag setting that
indicating that backup data
have not been copied

Writing F0 to the 2 k byte ROM

The backup ROM is
initialized.

[BCP]

To copy Digital backup data
to EEPROM

Copying backup data

When the DIGITAL Assy is to be replaced, adjustment values can be copied from the backup EEPROM to the EEPROM
of the Assy for service.

Содержание PDP-4270HD

















































































































































































































Результаты поиска

Содержание PDP-4270HD

Отзывы:

Похожие инструкции для PDP-4270HD

Бренды по названию

Популярные бренды

Pioneer PDP-4270HD, Руководство по обслуживанию

Результаты поиска

Содержание PDP-4270HD

Отзывы:

Похожие инструкции для PDP-4270HD

Бренды по названию

Популярные бренды