Pioneer PDP-4270HD Скачать руководство пользователя страница 92

Страница: 92 / 208

PDP-4271HD

5.1.7 FLOWCHART OF FAILURE ANALYSIS FOR THE AUDIO SYSTEM

Is a signal output from IC4701?
(pin 33, 34)

Check the surrounding of IC4701
and each input signal. If there was
no ploblem replace MAIN Assy.

Check the communication
between IC4701 and CN4005.

Replace the MAIN Assy.

Replace the TANSHI Assy.

Cansel muting then check again.

Is the volume set to 0?

Check around IC4704.

Yes

Has the signal come to TP8825
or TP8826?

Yes

The sound is not emitted audio out.

⇒

MONI_A

Has the signal arrived at CN4005?

Is a signal output from CN8803?

Is a signal output from jack?

Yes

No audio from monitor out

Yes

Has the sound been emitted from
the Subwoofer?

Yes

Is a signal output from IC4701?
(pin 31, 32)

Yes

Is a signal output from IC4704?
(pin 1, 7)

Has the signal arrived at CN4005?

Check the around of IC4701 and
each input signal. If there was no
ploblem, replace MAIN Assy.

⇒

SUB-W

No audio output from subwoofer

Finishing troubleshooting.

Check the Flexible cable between
CN4005 and CN8803.

Replace or reconnect flexible cable.

Check the contact between the
CN8803 and R8886.
Check the contact between the
CN8803 and R8887.

Check the communication between
IC4704 to CN4005.

Cansel muting then check again.

Replace the MAIN Assy.

Replace the TANSHI Assy.

Replace the MAIN Assy.

Yes

Is a signal output from CN8803?

Check the Flexible cable between
CN4005 and CN8803.

Yes

Has the signal come to TP8843?

Yes

Check the around of pin Jack.

Check the contact between the
CN8803 and R8892.

Replace or reconnect flexible cable.

Raise the volume then check again.

Check the communication
between the CN8803 and Jack.
If there was no ploblem replace
IO Assy.

Waveforms

Input signal: 1kHz
Sound volume is fixed to 25.

IC4701 - pin 33, 34 (AC)

V: 500 mV/div H: 400

sec/div

Waveforms

Input signal: 100 Hz
Sound volume is fixed to 25.

IC4704 - pin 1, 7 (DC-SUBWOO)

V: 500 mV/div H: 4 msec/div

IC4704 - pin 1, 7 (AC-SUBWOO)

V: 200 mV/div H: 4 msec/div

IC4701 - pin 31, 32 (DC-SUBWOO)

V: 1 V/div H: 10 msec/div

IC4701 - pin 31, 32 (AC-SUBWOO)

V: 200 mV/div H: 4 msec/div

Flowchart of Failure Analysis for The Audio System

Содержание PDP-4270HD

















































































































































































































Результаты поиска

Содержание PDP-4270HD

Отзывы:

Похожие инструкции для PDP-4270HD

Бренды по названию

Популярные бренды

Pioneer PDP-4270HD, Руководство по обслуживанию

Результаты поиска

Содержание PDP-4270HD

Отзывы:

Похожие инструкции для PDP-4270HD

Бренды по названию

Популярные бренды