Pioneer PDP-4270HD Скачать руководство пользователя страница 101

Страница: 101 / 208

PDP-4271HD

101

5.3.2 SD (SHUTDOWN) DIAGNOSIS

Frequency of

LED Flashing

Major Type

Detailed Type

Log Indication in Factory Mode

Checkpoint

Possible Defective

Part

Remarks

MAIN

SUB

Blue 1

Abnormality in the

Sequence Processor

Communication error

SQ-IC

RTRY

CLK_SQ/TXD_SQ, etc.

IC3151, IC3401

SQ_IC communication not established

Drive stop

SQNO

Check if the video sync signal is input to IC3401.

CN3001, IC3401

If the signal detection by the module microcomputer is properly performed, the unit operates on an external sync.

Busy

BUSY

BUSY_SQ

IC3401

If BUSY_SQ remains high, a shutdown is generated.

Incoherent version (hardware, software)

VER-HS

Check the model number of the DIGITAL Assy and the destination of the sequence processor.

IC3301, IC3401

The written SQ_PROG is incoherent with data on the DIGITAL Assy.

Blue 2

Failure in IIC

communication with the

module microcomputer

DIGITAL Assy EEPROM

MD-IIC

EEPROM

IIC communication line of IC3156

IC3151, IC3156

Check the pull-up resistor of the IIC control line and the power to the corresponding IC.

SENSOR Assy EEPROM

BACKUP

IIC communication line of IC3652

IC3151, IC3652

Check the pull-up resistor of the IIC control line and the power to the corresponding IC.

DAC

IIC communication line of IC3157

IC3151, IC3157

Check the pull-up resistor of the IIC control line and the power to the corresponding IC.

Blue 3

Abnormality in RST2

power decrease

–

RST2

–

Is the output voltage of the DC-DC converter low?

AXY1135

If RST2 does not become high after the unit is turned on, a shutdown will be generated in several seconds.

The 12 V power is not output.

POWER SUPPLY Unit

Check if V + 12 V is started.

Blue 4

High temperature of the

panel

–T

MP_NG

TEMP1

Ambient temperature

–

If TEMP1 that is read by the module microcomputer is 75

C or higher, a shutdown will be generated.

Abnormality in the panel temperature sensor

IC3651

Check the connection with the SENSOR Assy.

Blue 5

Short-circuiting of the

speakers

–

AUDIO

–

Speaker terminals

CN3753, CN3901, JA3901

Check if any speaker cable is in contact with the chassis.

AUDIO_AMP

IC3751

Check if the AMP output is short-circuited.

Periphery of the cable between A2 and M8

CN3752, CN4007

Check if cables are firmly connected.

Blue 6

Failure in communication with

the module microcomputer

–

MODULE

–

Communication line between MAIN and MOD

IC3151, IC8401

Check the communication lines (RXD_MOD/RXD_MOD/REQ_MOD).

Periphery of the cable between D11 and M2

CN3001, CN4001

Check if cables are firmly connected.

Blue 7

Failure in main

microcomputer 3-wire

serial communication

IF microcomputer

MA-SRL

Communication line between IF and MAIN

IC8301, IC8401

Check the communication lines (TXD_IF/RXD_IF/CLK_IF/BUSY_IF/CE_IF/REQ_IF).

MULTI

Communication line between MULTI_M and MAIN

IC8201, IC8401

Check the communication lines (TXD_IC3/RXD_IC3/CLK_IC3/CE_IC3/IC3_BUSY).

I/P

Bus communication line between IP and MULTI_M

IC8101, IC8201

Check the communication lines (EXA/EXDIO).

D_SEL

Communication line between D_SEL and MULTI_M

IC8001, IC8201

Check the communication lines (TXD_IC6/RXD_IC6/CLK_IC6/CE_IC6).

Blue 8

Failure in IIC

communication with the

main microcomputer

AV Switch

MA-IIC

AV-SW

IIC communication line between AV_SW and MAIN

IC4701, IC8401

Check the communication lines (SCL_AV3/SDA_AV3 or SCL_AV/SDA_AV

RGB Switch

RGB-SW

IIC communication line between RGB_SW and MAIN

IC4901, IC8401

Check the communication lines (SCL_AV3/SDA_AV3 or S

CL_AV/SDA_AV).

Analog Tuner

FE1

IIC communication line between A_Tuner and MAIN

U4401, IC8401

Check the communication lines (SCL_AV3/SDA_AV3 or SC

L_AV/SDA_AV).

Analog Tuner

FE2

IIC communication line between A_Tuner and MAIN

U4402, IC8401

Check the communication lines (SCL_AV3/SDA_AV3 or SC

L_AV/SDA_AV).

MPX

IIC communication line between MPX and MAIN

IC4402, IC8401

Check the communication lines (SCL_AV3/SDA_AV3 or SCL_AV/SDA_AV)

Main VDEC

M-VDEC

IIC communication line between M_VDEC and MAIN

IC5101, IC8401

Check the communication lines (SCL_MA/SDA_MA).

AD/PLL

ADC

IIC communication line between ADC and MAIN

IC5301, IC8401

Check the communication lines (SCL_MA/SDA_MA).

HDMI

IIC communication line between HDMI_RX and MAIN

IC5401, IC8401

Check the communication lines (SCL_MA/SDA_MA).

CCD

IIC communication line between CCD and MAIN

IC4601, IC8401

Check the communication lines (SCL_TXT/SDA_TXT).

64K EEPROM

MA-EEP

IIC communication line between EEPROM and MAIN

IC8409, IC8401

Check the communication lines (SCL_EP/SDA_EP).

VOLUME IC

AUDIO

IIC communication line between VOL_IC and MAIN

IC3753, IC8401

Check the communication lines (SCL_AUDIO/SDA_AUDIO).

VOLUME IC

AUDIO

Periphery of the cable between A2 and M9

CN3752, CN4007

Check if cables are firmly connected.

Blue 9

Failure in communication with the main microcomputer and unknown

MAIN

–

Communication line between IF and MAIN

IC8301, IC8303, IC8304, IC8401

Check the communication lines (TXD_IF/RXD_IF/CLK_IF/BUSY_IF/CE_IF/REQ_IF).

Blue 10

Failure in the fan

–

FAN

–

Dirt attached to the fan motor

–

Check the fan.

Periphery of the cable between fan and M4

CN4009

Check if cables are firmly connected.

Periphery of the fan control regulator

IC8407

–

Blue 11

High temperature of the

unit

–

TEMP2

–

Temperature sensor or its periphery

–

shutdown is generated if TEMP2 becomes higher than 53

Periphery of the temperature sensor

TH8901, Q8901

TEMP2

Periphery of the cable between T2 and M7

CN8802, CN4004

Check if cables are firmly connected.

Blue 12

Digital Tuner

–

DTUNER

PS/RST

Startup of IC6301

IC6301

Check startup of BCM7038 and the communication line between IC6301 and MAIN.

DEVICE

Communication line between MAIN and IC6301

IC6301

Check startup of BCM7038 and the communication line between IC6301 and MAIN.

TV-G

Startup of the TV-GUIDE application

IC6301

Check startup of the TV-GUIDE application. (

∗

)

HOME-G

Startup of the HOME-G application

IC6301

Check BCM7038 and its peripheral devices.

Blue 13

Failure in the POWER

SUPPLY Unit

DC-DC converter power decrease

MA-PWR

M-DCDC

DC-DC converter or its periphery, RST2

IC4102, Q4106

Check if V + 3.3 V is started.

POWER SUPPLY

RELAY

The 12 V power is not output, RST4

–

Check if V + 12 V is started.

Periphery of the cable between P8 and M2

CN4002

Check if cables are firmly connected.

(

∗

) : Check if it becomes banner display when switching channel.

Содержание PDP-4270HD

















































































































































































































Результаты поиска

Содержание PDP-4270HD

Отзывы:

Похожие инструкции для PDP-4270HD

Бренды по названию

Популярные бренды

Pioneer PDP-4270HD, Руководство по обслуживанию

Результаты поиска

Содержание PDP-4270HD

Отзывы:

Похожие инструкции для PDP-4270HD

Бренды по названию

Популярные бренды