Pioneer PDP-4270HD Скачать руководство пользователя страница 143

Страница: 143 / 208

PDP-4271HD

143

8.2.3 OPTION MODE

Operation item

8.2.3.1

EDID WRITE MODE

DISABLE ENABLE

8.2.3.2

ANTENNA MODE

CABLE AIR

8.2.3.3

AFT

Controls AFT action by turing ON / OFF

8.2.3.1 EDID WRITE MODE

Exclusively used for production line.

8.2.3.2 ANTENNA MODE

Receiving Cable/Air signal with equipped/unequipped DTB tuner.

When DTV tuner is equipped

It is effective during tuner function only (others are gray-downed). The currently viewed ANT

A/ANT B function’s cable/air (both analog and digital) signal are changed. The channel settings

are memorized (memorized by DTV side).

When DTV tuner is unequipped

It is possible for ANT A/ANT B function to receive air/cable signal.

Channel settings are not memorized. But after leaving factory mode, the settings are maintained.

If the air/ cable signal is changed, the reserved allocation map is written.

For example, if the signal is changed to air, then the air’s broadcast map is configured,

and cable’s broadcast map is destroyed.

If the signal is changed to cable, then the cable’s broadcast map is configured, and air’s

broadcast map is destroyed.

CABLE

Change the antenna setting to cable

AIR

Change the antenna setting to air

8.2.3.3 AFT

Exclusively used for production line.

No.

Function/Display

Content

RS232C

OSD display

Funcrion

Control device

Содержание PDP-4270HD

















































































































































































































Результаты поиска

Содержание PDP-4270HD

Отзывы:

Похожие инструкции для PDP-4270HD

Бренды по названию

Популярные бренды

Pioneer PDP-4270HD, Руководство по обслуживанию

Результаты поиска

Содержание PDP-4270HD

Отзывы:

Похожие инструкции для PDP-4270HD

Бренды по названию

Популярные бренды