Pioneer PDP-4270HD Скачать руководство пользователя страница 85

Страница: 85 / 208

PDP-4271HD

5.1.5 FLOWCHART OF FAILURE ANALYSIS FOR THE MAIN ASSY

Flowchart of Failure Analysis for The MAIN Assy

Failure in the RST IC (IC4801) output or its peripheral circuits

Yes

Replace the MAIN Assy.

The STB LED does not light although
STB 3.3 V power is supplied.

Is the M5 connector securely
connected?

Securely connect the M5 connector.

Yes

Is the cable that is connected to
the M5 connector broken?

Replace the cable (J113).

The RELAY port does not work.
The power is not turned on.

Is voltage at REQ_IF (3.3 V) on
the MAIN Assy high?

Is the power (1.8 V, 3.3 V) supplied
to the main microcomputer?

Can the unit be turned on, using
the remote control unit?

Can the unit be turned on, using
the Power switch on the side key?

Can the unit be turned on, using
RS-232C commands?

Yes

Is resetting of the IF
microcomputer canceled?

Failure in the line between the IF microcomputer and M5 connector

Failure in the RS-232C driver and its
peripheral circuits

If the voltage at Pin 129 (RST3 port) on the main
microcomputer is high, it is judged that the AC power
cord is not plugged in, and operation of the unit will stop there.

Replace the MAIN Assy.

Yes

Is the voltage at Pin 1 of the M5
connector low?

No problem with the MAIN Assy.
Check the LED Assy.

Yes

Replace the cable that connects
the LED IR and MAIN Assys.

Replace the cable that connects
the SIDE KEY and MAIN Assys.

Replace the LED IR Assy.

Replace the SIDE KEY Assy.

Replace the MAIN Assy.

Yes

Failure analysis for the
MAIN Assy.

⇒

MA1

Failure analysis for the
MAIN Assy.

⇒

MA2

Содержание PDP-4270HD

















































































































































































































Результаты поиска

Содержание PDP-4270HD

Отзывы:

Похожие инструкции для PDP-4270HD

Бренды по названию

Популярные бренды

Pioneer PDP-4270HD, Руководство по обслуживанию

Результаты поиска

Содержание PDP-4270HD

Отзывы:

Похожие инструкции для PDP-4270HD

Бренды по названию

Популярные бренды