Pioneer ELITE VSX-LX505 Скачать руководство пользователя страница 170

Страница: 170 / 212

170

Setup

Measuring with Full Auto MCACC

Place the supplied speaker setup microphone in the listening position, measure

the test tones emitted by the speakers, then the unit automatically sets the

optimum volume level for each speaker, the crossover frequencies, and the

distance from the listening position. This also reduces the effect of the standing

wave in accordance with the viewing environment and automatically adjusts the

equalizers for the speakers and enables correction of distortion caused by the

acoustic environment of the room.

•

Calibration takes between 3 and 12 minutes to be completed.

1. Place the supplied speaker setup microphone at the listening position, and

connect it to the SETUP MIC jack on the main unit.

SETUP MIC

When placing the speaker setup microphone on a tripod, refer to the

illustration.

Confirm a test tone is output from the subwoofer and press ENTER.

3. Press ENTER to output test tones from each speaker, and the connected

speakers and the noise in the surrounding environment are automatically

measured.

4. The measurement results in step 3 are displayed. If there is no problem in

the detection result of the speaker, select "Next" and press ENTER to output

the test tone again to automatically set the settings such as volume level,

crossover frequency, etc., to their optimum. (The test tone is automatically

output when 10 seconds has elapsed without any operation.)

•

When an error message is displayed or when the connected speakers

cannot be detected, perform re-measurement by selecting "Retry" and

pressing ENTER.

• When it cannot be resolved by performing the re-measurement, confirm

if the speakers are connected correctly. If there is any problem with the

speaker connection, perform the connection after disconnecting the power

cord.

5. Once the measurement is completed, it is possible to perform the

measurement in 8 additional listening positions. To perform the measurement,

select "Next" and press ENTER, then follow the instructions. To not perform

the measurement, select "Finish (Calculate)" and press ENTER.

•

After each listening position is detected, select "Finish (Calculate)" and

press ENTER to complete the detection process.

6. Disconnect the speaker setup microphone.

Содержание ELITE VSX-LX505





















































































































































































































Результаты поиска

Содержание ELITE VSX-LX505

Отзывы:

Похожие инструкции для ELITE VSX-LX505

Бренды по названию

Популярные бренды

Pioneer ELITE VSX-LX505, Инструкция по эксплуатации

Результаты поиска

Содержание ELITE VSX-LX505

Отзывы:

Похожие инструкции для ELITE VSX-LX505

Бренды по названию

Популярные бренды