Pioneer Elite SC-97, Руководство по эксплуатации

Страница: 124 / 171

124
FAQ
13
Symptom Remedy
When
HDZONE
is
ON
, multi-channel
audio sources are not output in the
main zone.
When
HDZONE
is selected in
Speaker System
and also the same HDMI input is selected
for both the main zone and HDZONE, 2-channel PCM audio sources are output from the
main zone as well. To output multi-channel audio sources, set
HDZONE to OFF or change
the HDZONE input.
No HDZONE sound is output. With HDZONE, multi-channel audio may not be output. In this case, set the audio output
setting of your playback device to 2-channel PCM.
BT AUDIO
Symptom Remedy
The Bluetooth wireless technology
device cannot be connected or oper-
ated. Sound from the
Bluetooth wire-
less technology device is not emitted
or the sound is interrupted.
Check that no object that emits electromagnetic waves in the 2.4 GHz band (microwave
oven, wireless LAN device or
Bluetooth wireless technology apparatus) is near the unit. If
such an object is near the unit, set the unit far from it. Or, stop using the object emitting
the electromagnetic waves.
Check that the
Bluetooth wireless technology device is not too far from the unit and that
obstructions are not set between the Bluetooth wireless technology device and the unit.
Set the Bluetooth wireless technology device and the unit so that the distance between
them is less than about 10 m (33 ft.) and no obstructions exist between them.
The
Bluetooth wireless technology device may not be set to the communication mode
supporting the Bluetooth wireless technology. Check the setting of the Bluetooth wireless
technology device.
Check that pairing is correct. The pairing setting was deleted from this unit or the
Blue-
tooth wireless technology device. Reset the pairing.
Check that the profile is correct. Use a Bluetooth wireless technology device that sup-
ports A2DP profile and AVRCP profile.
Video
Symptom Remedy
No image is output when an input is
selected. Check the video connections of the source component.
For HDMI, or when
V.CONV is set to OFF and a TV and another component are con-
nected with different cords (in Setting the Video options on page 91 ), you must connect
your TV to this receiver using the same type of video cable as you used to connect your
video component. For the component video input, however, signals are only output from
the
HDMI OUT 1 or HDMI OUT 2 terminal, so when using the component video input,
set V.CONV to ON .
Make sure the input assignment is correct for components connected using component
video or HDMI cables (see
The Input Setup menu on page 61 ).
Check the video output settings of the source component.
Check that the video input you selected on your TV is correct.
Some components (such as video game units) have resolutions that may not be con-
verted. If adjusting this receiver’s Resolution setting (in
Setting the Video options on
page 91 ) and/or the resolution settings on your component or display doesn’t work, try
switching V.CONV (in Setting the Video options on page 91 ) to OFF .
When the device is connected using an HDMI OUT terminal, press the remote con-
trol’s OUT P. button to check the HDMI OUT output setting. For OUT 3 , also check the
MAIN/HDZONE setting at ZONE Setup .
When the HDMI OUT 1/2 setting of the output parameter function is set to OFF , set it to ON .
If HDZONE is set to on, video images connected using a video cable or component cable are
not output from the HDMI terminal. To output video images, turn HDZONE off (
page 95 ).
When content that is protected by the HDCP 2.2 protocol is output from a source player,
output of video is not possible on televisions and projectors that do not support HDCP
2.2. Please prepare a television or projector that supports HDCP 2.2. Also, this receiver’s
HDCP 2.2 compatible input terminals are
BD , HDMI IN 1 , and HDMI IN 2 . When making
connections other than the said terminal(s), please use these terminals instead.
Noisy, intermittent, or distorted
picture. Sometimes a video deck may output a noisy video signal (during scanning, for example),
or the video quality may just be poor (with some video game units, for example). The pic-
ture quality may also depend on the settings, etc. of your display device. Reconnect the
source and display device using the same type of connection (component or composite),
then start playback again.
Video signals are not output from the
component terminal. When a monitor only compatible with resolutions of 480i is connected to the component
terminal and another monitor is connected to the HDMI terminal, the video signals may
not be output to the monitor connected to the component terminal. If this happens, do
the following:
— Turn off the power of the monitor connected to the HDMI terminal.
— Change the
VIDEO P. menu SCAL setting (see Setting the Video options on page 91 ).
— Video signals from the HDMI terminal cannot be output to the component terminals.
Input the video signals from the player or other source to the composite or component
terminals. When using the component terminal, assign it at
Input Setup (see The Input
Setup menu on page 61 ).
The picture’s movement is unnatural. When Resolution under VIDEO PARAMETER is set to 1080/24p or 4K/24p , the picture
may not be displayed properly for some source materials. In this case, set the resolution
to something other than 1080/24p or 4K/24p (
page 91 ).
Video parameters cannot be used. For audio only input (TUNER, CD, and TV), the video parameter function cannot be used.
Use for video or input with a GUI display.
Cannot be used when the HDZONE is ON. Turn OFF the HDZONE.