Pine Research MSR 636A Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 176

Pine Research MSR 636A Скачать руководство пользователя страница 34

28

3

Installation

3.1

Site Preparation

The rotator system should be located on a sturdy table or laboratory bench with
ample clearance around the perimeter of the rotator enclosure. The front of the
rotator should be unobstructed, and there should be at least 20 cm clearance on
each side and behind the rotator, for a total table space of 40 cm x 60 cm. The
location should also include enough space for the control unit
(30 cm x 30 cm) and vertical clearance to easily raise and lower the motor unit.

3.2

Unpacking and Setting Up the Rotator

Note:
The numbers in parentheses in the installation instructions
(below) correspond to the numbering used in the tables and
figures found in Section 2 of this manual.

Inspect  the  contents  of  the  shipping  carton.
Remove the top piece of cardboard to reveal
the  two  smaller  boxes  in  the  carton.  The
control  unit

(10)

is packed inside the larger

box,  and  the  smaller  box  holds  additional
components.  Remove  both  boxes  and  set
aside.  Then,  carefully  remove  the  enclosure
window

(7)

and the enclosure base

(4)

from

the box. The center post

(1)

is pre-installed in

the enclosure base.

Open the smaller box. It should contain the
motor unit

(2)

, the support collar

(5)

, the cell

platform

(3)

, the side post

(6)

, a standard

three-pronged  laboratory  clamp  (with  right-
angle  mount),  and  a  small  bag  containing
two  banana  cables  and  some  additional
assembly hardware.

Note:
The outer diameter of the side post (6) shown in these photos is
5/8" (15.9 mm), but in some alternate rotator configurations this
diameter may be 1/2" (12.7 mm).

«
...
32
33
34
35
36
...
»

Содержание MSR 636A

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды