Pine Research MSR 636A Скачать руководство пользователя страница 165

Страница: 165 / 176

MSR Rotator Control by Pine Potentiostats

DRK10057 (REV002 | MAR 2016)

Page 2

Figure 2. The Rotation Rate Control Cable (AKCABLE4) for Connecting a Pine Potentiostat to an MSR Rotator.

Compatible Pine Potentiostats

Any potentiostat that has an analog output feature can be integrated to the rotator control unit to control the

rotation rate. The following Pine potentiostats are capable of controlling the rotator through AfterMath software:

•

WaveNow Potentiostat/Galvanostat System (AFTP1)

•

WaveNano Potentiostat/Galvanostat System (AFTP2)

•

WaveNowXV Potentiostat/Galvanostat System (AFTP3)

•

WaveDriver 10 Potentiostat/Galvanostat System (AFP1)

•

WaveDriver 20 Bipotentiostat/Galvanostat System (AFP2)

Note, that while the CBP Bipotentiostat/Galvanostat System (AFCBP1) is capable of running on AfterMath software,

it does not have an analog output feature. Therefore, the CBP is not compatible with MSR Rotator rotation rate

control.

If “Rotator methods” is not available under the “Experiments” heading in the menu bar of AfterMath, a new

AfterMath instrument license may be required to enable “Rotator methods”. If the rotator was purchased after the

potentiostat was purchased, a “Rotator methods” capable license was likely not issued for the potentiostat at the

time of purchase. Please contact Pine directly to update the AfterMath license.

Pine Potentiostat to MSR Rotator Connections

Compatible Pine potentiostats use the rotation rate control cable (AKCABLE4) to connect the analog output of the

potentiostat to the analog input of the control unit; this cable can be purchased from Pine Research Instrumentation

(see: Figure 2). It ships with any rotator/potentiostat bundle purchased from Pine and can be purchased separately

at any time. The connections shown are only for use between compatible Pine potentiostats and MSR Rotators. To

connect a potentiostat from a different manufacturer to the MSR Rotator, contact your representative at the

potentiostat manufacturer for details and cable options.

In addition to controlling the rotation rate, a digital stop line connects the Pine potentiostats to the MSR Control Unit.

When the knob on the front of the control unit is set to

𝑅𝑅𝑅𝑅𝑅𝑅

, residual power is still sent to the motor (so the rotation

Содержание MSR 636A

















































































































































































Результаты поиска

Содержание MSR 636A

Отзывы:

Бренды по названию

Популярные бренды

Pine Research MSR 636A, Руководство пользователя

Результаты поиска

Содержание MSR 636A

Отзывы:

Бренды по названию

Популярные бренды