Pine Research MSR 636A Скачать руководство пользователя страница 110

Страница: 110 / 176

104

Turn the rotation rate knob fully counter-clockwise. This is the position which
corresponds to a nearly zero rotation rate.

Reconnect the power cord and carefully switch on the rotator.

Slowly turn the rotation rate control knob fully clockwise to the fastest rotation
rate. The rotation rate display on the front panel of the control unit should read
approximately 10050 RPM. Adjust trimmer

until the rotation rate display on

the front panel of the control unit reads

10050 RPM

± 10 RPM.

Turn the rotation rate knob fully counter-clockwise. This is the position which
corresponds to a nearly zero rotation rate.

Switch off power to the rotator and disconnect the power cord.

Replace the cover on the control unit.

At this point the calibration procedure is complete. Make a note in a log book
or place a sticker on the control unit to record the calibration date.

Содержание MSR 636A

















































































































































































Результаты поиска

Содержание MSR 636A

Отзывы:

Бренды по названию

Популярные бренды

Pine Research MSR 636A, Руководство пользователя

Результаты поиска

Содержание MSR 636A

Отзывы:

Бренды по названию

Популярные бренды