background image

6.5.5. Service intervals

The hydraulic unit is filled with OPTIMA HV46 hydraulic oil, for which it is recommended to replace the oil within a time 
interval shorter than 4,500 operating hours, along with the return filter, or once in a year depending on what occurs first. 
Replace the return filter each 1,500 operating hours (MANN FILTER W 79 supplied by the manufacturer). Consistently 
check the oil level on the gauge located on the filling cap on the hydraulic unit in the machine base. The oil level must be 
maintained between the two oil marks.

6.5.6. Oil Refill and Filter Replacement

• Unscrew the return oil filter.
• Remove the lid of the hydraulic unit by unscrewing the twelve M10 bolts.
• Very carefully raise the lid and make sure the sealing does not stick to the lid or the tank, leading to its damage.
• If the sealing is damaged, replace it for a new one. Never use a damaged sealing, otherwise you risk contamination of the hydraulic 
system by the remnants of cork sealing.
• When replacing the oil, pour out the old oil and clean the tank. A cloth is a sufficient tool for cleaning, but it must be non-linting. You 
can use a solution that does not disturb the tank coating and does not leave residues in the tank. After the cleaning, check the inside of 
the tank thoroughly.  Check the condition of the oil-resistant coating.  Should any flaking or poor quality manifest themselves, remove 
the coating with an appropriate solvent, wash, dry and clean with pressure air. In this way, failures caused by the deteriorated coating, 
which contaminates the entire hydraulic system, will be prevented.
• Once the tank is clean and free from deposits, place the lid and the sealing back on the tank using a reverse procedure and cross-
tighten the screws.
• Pour in new oil. Only oil recommended by the equipment manufacturer can be filled in.  Never refill directly from barrels. Always use 
a filter unit with filters with a mesh density lower than 25 µm.   Using filters with contamination indication improves the quality and 
convenience of the work. Consistently check the oil level on the gauge located on the filling cap. 

The oil level must be maintained 

between the two oil marks.

• Unscrew the new return oil filter.
• check the piping for noise and leakage.
• Start the hydraulic unit within short intervals.
• Vent the hydraulic circuit. Venting is performed usually by raising and descending the arm, clamping and unclamping the vice. 
Repeat several times, until the system is ventilated (usually 5-10 times).

Caution: Oil and the filter are classified as special waste!

7. Faults and Remedies

7.1. Repairs

HM 32

HM 46

CETOP RP 91 H Specifications

AGIP

ARAL

BP

CASTROL

ESSO

MOBIL

MOGUL

OLEA

ÖMV

PARAMO

SHELL

VALVOLINE

OSO 32

VITAM GM 32

ENERGOL HLP 32

HYSPIN AXS 32

NUTO H 32

MOBIL DTE 24

MOGUL HM 32

OPTIMA HM 32

HLP 32

PARAMOL HM 32

TELLUS OIL 32

ULTRAMAX AW 32

VITAM GF 46

ENERGOL HLP 46

HYSPIN AWS 46

NUTO H 46

MOBIL DTE 25

MOGUL HM 46

OPTIMA HM 46

HLP 46

PARAMOL HM 46

TELLUS OIL 46

ULTRAMAX AW 46

OSO 46

6.5.4. Hydraulic Mineral Oils

HM performance class according to CETOP RP 91H European specification in viscosity classes ISO VG 32 and 46. Oils marked as 
HM 32 are recommended for use in environment with ambient temperatures reaching 0 °C and below 0 °C. HM 46 oil types are 
recommended for use in environment with ambient temperatures within the range +5 °C and +40 °C.

Caution! Danger of injury!
Carry out repairs only when the master switch is off or secured against switching on or when the machine is 
isolated  from  the  power  supply  and  secured  against  restarting.  The  saw  arm  must  always  be  supported 
mechanically in the lower position while it is being repaired - see section 3.5. We recommend to contact an 
authorised service centre for repairs.

Содержание ARG 300 DCT CF-NC automat






















































Отзывы: