background image

Use eyes and ears protection!

Use protective gloves!

Dangerous place caution -
be very careful!

Caution of dangerous electrical voltage!

Read the instruction manual carefully and make 
sure you understood its content before using the 
machine!

Necessary to use high boots or hard duty 
shoes with protective steel forepart and 
anti-sliding sole!

Warranty letter - service

Warranty letter is a separate part of the instruction manual.

Warranty period length:

 see warranty letter.

Terms of validity of the warranty letter 

:

• Machine transport, manipulation and storage according to the instruction manual.
• Machine usage, operation and maintenance according to the instruction manual.
• Machine connection to the electrical grid supply according to the instruction manual.

The warranty letter does NOT include :

•The machine user´s or third person violent and mechanical machine damage.
• Remediless event (elementary disaster).
• Machine damage during transport.
• Machine storage or placing in wet, chemical or otherwise dangerous environment.

0. In general

This instruction manual provides the users assistance and information about the PILOUS bandsaw and the possibilities of use 
corresponding to its purpose. The instruction manual contains important instructions for a safe, adequate and economically efficient 
operation. Observing the operating instructions will prevent hazards, reduce the repair and outage time costs, and increase the 
machine reliability of a system. The instruction manual must always be available at the machine site. The instruction manual must be 
read and used by the staff entrusted with the machine installation, transport and storage, use/operation, maintenance and disposal. 
In addition to the instruction manual and the binding rules related to accident prevention valid in the user´s country and at the service 
site. It is also necessary to observe the approved rules for safe and professional work.

Address any possible comments on the warranty letter by fax, or mail to the address shown on the warranty 
letter.

Notice for the user:

The seller is obliged to issue warranty letter to the user when the product is dispatched. The warranty letter must be signed and 
confirmed by the seller´s stamp with the date of issue and product serial number. The seller is obliged to introduce the product to the  
user. 

Data needed to apply for the warranty (after warranty) machine repair:

• Machine type
• Warranty letter number (same as machine serial number)
• Warranty letter issue date

0.1.   Safety provisions

The machine design complies with the technical status and the approved safety and technical rules. In spite of this the  user's or the 
third persons' health can be endangered and/or the machine or other tangible goods may be unfavorably influenced during the 
operation of the machine. In order to prevent such hazards it is unconditionally necessary to observe the safety instructions in this 
instruction manual. These safety instructions must be read and understood by the respective persons before the machine has been 
put into operation. Failure to observe these instructions may cause serious property damage and damage to health! The safety 
instructions are marked in this instruction manual with safety symbols / danger spot signs.

Содержание ARG 180







































Отзывы: