PIAGGIO MP3 400 hpe E5 2021 Скачать руководство пользователя страница 95

Страница: 95 / 126

Removing the piston

- Insert the pin.

- Insert the retainer rings.

CAUTION

POSITION THE ARROW PRINTED ON THE PISTON
CROWN TOWARDS THE EXHAUST OPENING.

CAUTION

AT EVERY NEW MOUNTING USE RETAINER RING PINS.

Choosing the gasket

- Provisionally fit the piston into the cylinder, without any base gasket.

- Assemble a dial gauge on the specific tool.

Specific tooling

020921Y

Piston position checking tool

- Using an abutment plane, reset the dial gauge

with a pre-load of a few millimetres.

- Finally fix the dial gauge.

- Check the perfect sliding of the feeler pin.

- Install the tool on the cylinder without changing

the dial gauge position.

- Lock the tool using the original head fixing nuts.

- Rotate the crankshaft up to the TDC (the inver-

sion point of the dial gauge rotation).

- Measure the deviation from the reset value.

- By means of the table, see the Specifications chapter identify the cylinder base gasket thickness to

be used for refitting. Correctly identify the cylinder base gasket thickness to keep the correct compres-

sion ratio.

- Remove the special tool and the cylinder.

See also

MP3 400 hpe E5

Engine

ENG - 95

Содержание MP3 400 hpe E5 2021































































































































Результаты поиска

Содержание MP3 400 hpe E5 2021

Отзывы:

Бренды по названию

Популярные бренды

PIAGGIO MP3 400 hpe E5 2021, Руководство по обслуживанию

Результаты поиска

Содержание MP3 400 hpe E5 2021

Отзывы:

Бренды по названию

Популярные бренды