PIAGGIO MP3 400 hpe E5 2021 Скачать руководство пользователя страница 75

Страница: 75 / 126

Refitting the ub cover

- Working in reverse order to the removal and us-

ing the specific tool, insert the control pinion, use

the recommended product and tighten the torque.

CAUTION

FOR THE INSTALLATION, ALWAYS USE NEW NUTS AL-
READY PROVIDED WITH SCOTCH GRIP.

Specific tooling

020918Y

Clutch lock

Locking torques (N*m)

M12x1.25 gear clutch shaft retainer nut

95 ÷ 105

- Pay attention to the correct positioning of the

alignment dowels.

- Thoroughly clean the surfaces of the engine

crankcase and reduction cover and seal, with the

recommended product, the matching surface

around the entire outer perimeter of the duct that

leads to the breather.

CAUTION

AN IMPROPER SEALING OF THE VENTILATION CIRCUIT
MEANS A LOSS OF OIL INTO THE AUTOMATIC TRANS-
MISSION HOUSING.

Recommended products

THREE BOND TB1207B

Liquid sealant

Three Bond liquid gasket TB1207B

- Remove the gasket.

- Insert the gears of the reduction unit in the re-

duction cover and tighten the screws to the speci-

fied torque, tightening in crossed sequence.

- Check the correct the tightening drainage screw.

Locking torques (N*m)

Final reduction cover screws

24 ÷ 27

Reduction

unit oil drainage screw

15 ÷ 17

CAUTION

THE FOLLOWING OIL REDUCTION FILLING PROCEDURE MUST BE CARRIED OUT ONLY WITH
THE MOTOR FITTED ON THE VEHICLE, ON THE CENTRE STAND IN FLAT LAND.

MP3 400 hpe E5

Engine

ENG - 75

Содержание MP3 400 hpe E5 2021































































































































Результаты поиска

Содержание MP3 400 hpe E5 2021

Отзывы:

Бренды по названию

Популярные бренды

PIAGGIO MP3 400 hpe E5 2021, Руководство по обслуживанию

Результаты поиска

Содержание MP3 400 hpe E5 2021

Отзывы:

Бренды по названию

Популярные бренды