PIAGGIO MP3 400 hpe E5 2021 Скачать руководство пользователя

Страница: 11 / 126

ASR warning light «

» turning on with slow flash-

ing.

• Accelerate to a constant speed of 30 to 40 km/h

and maintain it for at least to 8 seconds. The con-

tinuity of the vehicle speed in the correct field to

complete the procedure will be confirmed by a very

fast flashing of the ASR warning light «

».

• The end of the procedure will be indicated by the

steady lighting ASR warning light «

». The ASR

system is not active.

• Once the procedure is complete it is necessary

to switch to «

OFF

» and wait for at least 60 seconds

before being able to switch again to «

».

• In case of failure to complete the procedure within

5 minutes the ASR warning light «

» will stay on

steady and the ASR will remain off until switching

to «

OFF

».

• To switch again to «

» it is necessary to reac-

tivate the ASR. It is however necessary to repeat

the process until it succeeds.

Aesthetic inspection

Appearance check:

- Paintwork

- Fitting of plastics

- Scratches

- Dirt

Tightening torques inspection

Safety locks check

- Safety fasteners

- Fastening screws

Safety fasteners:

•

Rear shock absorber upper fixing

•

Rear shock absorber lower fixing

•

Front shock absorber upper fixing

MP3 400 hpe E5

Pre-delivery

PRE DE - 11

Содержание MP3 400 hpe E5 2021































































































































Результаты поиска

Содержание MP3 400 hpe E5 2021

Отзывы:

Похожие инструкции для MP3 400 hpe E5 2021

Бренды по названию

Популярные бренды

PIAGGIO MP3 400 hpe E5 2021, Руководство по обслуживанию

Результаты поиска

Содержание MP3 400 hpe E5 2021

Отзывы:

Похожие инструкции для MP3 400 hpe E5 2021

Бренды по названию

Популярные бренды