PIAGGIO MP3 400 hpe E5 2021 Скачать руководство пользователя страница 107

Страница: 107 / 126

- After removing the oil bulkhead, blow and clean

thoroughly before fitting.

Inspecting the crankshaft components

N.B.

TO MEASURE WEAR LIMITS AND COUPLING CLEARANCES, SEE THE SPECIFICATIONS CHAP-
TER.

Inspecting the crankshaft alignment

N.B.

TO MEASURE WEAR LIMITS AND COUPLING CLEARANCES, SEE THE SPECIFICATIONS CHAP-
TER.

See also

Crankcase - crankshaft - connecting rod

Inspecting the crankcase halves

- Before proceeding to check the crankcase

halves, thoroughly clean all surfaces and oil ducts.

- On the transmission-side crankcase half, take

particular care when handling the oil pump com-

partment and the oil ducts, the by-pass duct, the

main bushings and the cooling jet on the trans-

mission side (see diagram).

- Take particular care, also, that there are no signs

wear in the oil by-pass valve housing (see Chapter

Lubrication), as this could prevent a good seal in

the piston, which regulates the oil pressure.

- On the flywheel side crankcase half, take partic-

ular care cleaning the oil ducts for the main bush-

ings, the oil duct for the jet that lubricates the

cylinder head and the oil drainage duct at the fly-

wheel side oil seal.

MP3 400 hpe E5

Engine

ENG - 107

Содержание MP3 400 hpe E5 2021































































































































Результаты поиска

Содержание MP3 400 hpe E5 2021

Отзывы:

Бренды по названию

Популярные бренды

PIAGGIO MP3 400 hpe E5 2021, Руководство по обслуживанию

Результаты поиска

Содержание MP3 400 hpe E5 2021

Отзывы:

Бренды по названию

Популярные бренды