PIAGGIO MP3 400 hpe E5 2021 Скачать руководство пользователя страница 106

Страница: 106 / 126

Splitting the crankcase halves

- Undo the twelve crankcase coupling screws.

- Separate the crankcase halves while keeping the

crankshaft in one of these two halves.

- Only after the halves have been separated, can

the crankshaft be checked.

CAUTION

WHILE OPENING THE CRANKCASES AND REMOVING
THE CRANKSHAFT, CHECK THAT THE THREADED
SHAFT ENDS DO NOT INTERFERE WITH THE MAIN BUSH-
INGS. FAILURE TO OBSERVE THIS PRECAUTION CAN
DAMAGE THE MAIN BUSHINGS.

CAUTION

KEEP THE CRANKSHAFT IN ONE OF THE TWO HALVES
OF THE CRANKCASE WHEN SEPARATING IT. IF YOU FAIL
TO DO THIS, THE CRANKSHAFT MIGHT ACCIDENTALLY
FALL.

- Remove the gasket and be careful with the align-

ment dowels.

- Remove the by-pass and the oil bulkhead.

Engine

MP3 400 hpe E5

ENG - 106

Содержание MP3 400 hpe E5 2021































































































































Результаты поиска

Содержание MP3 400 hpe E5 2021

Отзывы:

Бренды по названию

Популярные бренды

PIAGGIO MP3 400 hpe E5 2021, Руководство по обслуживанию

Результаты поиска

Содержание MP3 400 hpe E5 2021

Отзывы:

Бренды по названию

Популярные бренды