PIAGGIO MP3 400 hpe E5 2021 страница 103 Скачать руководство пользователя

Страница: 103 / 126

- Tighten up the nuts to an initial pre-torque of 9-11

± 1 Nm.

- Tighten up the nuts by rotating 270.0±5.0° with

crossed sequence.

- Fit the two screws on the outside of the timing

chain side and tighten them to the specified torque.

N.B.

BEFORE INSTALLING THE HEAD, MAKE SURE THAT THE
LUBRICATION CHANNEL IS CLEAN USING A COM-
PRESSED AIR JET.

CAUTION

ALWAYS USE A NEW HEAD GASKET UPON REFITTING.

Locking torques (N*m)

Screws fixing cylinder head to crankcase

20 ÷

Cylinder head nut (PRE-TIGHTENING)

6 ÷ 8

Cylinder head nut (TIGHTENING)

9 ÷ 11 (Tighten

to 9 ÷ 11 Nm then proceed for 270.0° ±5.0° of rotation)

Fit the pins and rocking levers.

- Lubricate the two rockers through the upper

holes.

- Lubricate the two housings and insert the cam-

shaft in the cylinder head with the cams opposing

the rockers.

- Insert the calibrated pads and block the sliding of

the rockers by inserting the lock.

- Insert the retention plate and tighten the three

screws locking them to the specified torque. Clean

any threadlock remains from the seats, do not use

threadlock, the new screws to use during mounting

have scotch-grip application.

CAUTION

FOR THE INSTALLATION, ALWAYS USE NEW NUTS AL-
READY PROVIDED WITH SCOTCH GRIP.

Locking torques (N*m)

Containing plate retainer screws

4.5 ÷ 5.5

MP3 400 hpe E5

Engine

ENG - 103

Содержание MP3 400 hpe E5 2021































































































































Результаты поиска

Содержание MP3 400 hpe E5 2021

Отзывы:

Похожие инструкции для MP3 400 hpe E5 2021

Бренды по названию

Популярные бренды

PIAGGIO MP3 400 hpe E5 2021, Руководство по обслуживанию

Результаты поиска

Содержание MP3 400 hpe E5 2021

Отзывы:

Похожие инструкции для MP3 400 hpe E5 2021

Бренды по названию

Популярные бренды