PIAGGIO MP3 400 hpe E5 2021 Скачать руководство пользователя страница 113

Страница: 113 / 126

- Check that the oil pressure is between 3.2 and

4.2 bar with the engine running at 6000 rpm and

the oil at the required temperature.

- Remove the appropriate tools once the meas-

urement is complete, refit the oil pressure switch

and washer, tightening it to the specified torque

and fit the flywheel cover.

- If the oil pressure is not within the specified limits,

in the following order, check: the oil filter, the oil

by-pass valve, the oil pump and the crankshaft

seals.

N.B.

THE CHECK MUST BE CARRIED OUT WITH OIL AT THE
CORRECT LEVEL AND WITH AN OIL FILTER IN PROPER
CONDITION.

Characteristic

Oil pressure

Operating pressure

- At 1650 rpm: 0.5 - 1.2 bar

- At 6000 rpm: 3.2 - 4.2 bar

Locking torques (N*m)

Minimum oil pressure sensor

12 ÷ 14

Crankshaft oil seals

Removal

- Unscrew the three screws and remove them,

complete with the copper gaskets.

MP3 400 hpe E5

Engine

ENG - 113

Содержание MP3 400 hpe E5 2021































































































































Результаты поиска

Содержание MP3 400 hpe E5 2021

Отзывы:

Бренды по названию

Популярные бренды

PIAGGIO MP3 400 hpe E5 2021, Руководство по обслуживанию

Результаты поиска

Содержание MP3 400 hpe E5 2021

Отзывы:

Бренды по названию

Популярные бренды