background image

PSI-MOS-RS232/FO 1300 E

103266_en_02

PHOENIX CONTACT

16 / 17

11.3

DTE/DCE adjustment

You can use the DTE/DCE slide switch (9 in Figure 3 on 

page 9) to cross the TxD and RxD cables internally. This al-

lows for easy adjustment to DTE or DCE interfaces.

DTE: 

Connection to data terminal equipment

Set the switch to "DTE" (default setting for most applica-

tions).

DCE: 

Connection to data communication equipment

Set the switch to "DCE."

If you do not know which type of interface is connected, you 

can determine the right configuration by testing the 

DTE/DCE slide switch.

11.4

Wiring the switch contact

The device is equipped with a floating switching output for 

error diagnostics (terminals 

3

 (11) and 

4

 (12)).

The switch contact opens on the relevant device in the event 

of the following:

Supply voltage failure

An interrupt is detected on the fiber optic path

System reserve of the fiber optic path not reached. 

The switching output is an N/C contact. It can be connected 

to a local digital input, e.g. on a PLC, for error detection.

When a topology is used, the individual switching outputs 

can be connected to separate input points or the individual 

contacts can be looped through to generate a group mes-

sage.

Figure 13

Individual and group message

NOTE: Device damage

The maximum load capacity of the relay contact is 

1 A at 18...32 V DC.

2

4 V   

0

 V

2

4 V 

DC

2

4 V   

0

 V

2

4 V   

0

 V

2

4 V   

0

 V

2

4 V   

0

 V

2

4 V 

DC

Содержание PSI-MOS-RS232/FO 1300 E


















Отзывы: