background image

PSI-MOS-RS232/FO 1300 E

103266_en_02

PHOENIX CONTACT

10 / 17

8

Definition of fiber optic diagnostics

The quality of the path is determined using the incoming op-

tical power P

opt

 and displayed using the LED bar graph. 

You use DIP 2 to switch idle senders (reset period between 

sending data) to continuous illumination (INVERS). This al-

lows for continuous fiber optic diagnostics.

If you switch DIP 2 to "ON" (NORM), the diagnostics are not 

available via the LED bar graph.

As soon as the system reserve is reached, only the yellow 

LED remains lit. At the same time, the signaling relay drops 

and the switch contact opens. Data communication is still 

possible.

Basic method of operation

The device has three interfaces for the RS-232 signal:

Electrical interface (D-SUB)

Fiber  optic  port

DIN rail connector

You can change communication between the ports via 

DIP 1. This allows you to implement point-to-point or star 

structures.

8.1

Port assignment for point-to-point connections

The electrical interface communicates with the fiber optic 

port by means of full duplex mode. Internal data communi-

cation is disabled via the DIN rail connector.

Terms

DIP 1 = "OFF" (LINE)

One RS-232 device at each fiber optic coupler

The RS-232 devices can be addressed via communica-

tion software. 

Up to 6 fiber optic converters in a linear structure

Figure 4

Port assignment for point-to-point connections

8.2

Port assignment for star structures

By means of full duplex mode, the electrical interface com-

municates with all connected fiber optic ports of the star 

coupler via the DIN rail connector. Therefore internal data 

communication is in the direction of the master (electrical in-

terface). Telegrams from the master are output to the fiber 

optic ports of all connected devices via the DIN rail connec-

tor. 

The telegrams received at the fiber optic ports of the slaves 

are forwarded to the master exclusively via the DIN rail con-

nector. No telegrams are exchanged between the slaves. 

Terms

DIP  1  =  "ON"  (STAR)

One RS-232 device at each fiber optic port

Only connect the master to the star coupler.

The RS-232 devices can be addressed via communica-

tion software. 

Figure 5

Star structure port assignment

LED bar 

graph

Receive 

status

Optical power P

opt

Green

Green

Yellow

Very good

P

opt

 is significantly greater 

than the system reserve

Green

Yellow

Good

P

opt

 is still greater than the 

system reserve

Yellow

Critical

P

opt

 has reached the system 

reserve

Red

Error

P

opt

 has sapped the system 

reserve/broken fiber

If you switch DIP 2 to "ON", the FO diagnostics 

are not available via the LED bar graph.

The LED bar graph can light up at high transmis-

sion speeds or flash at low transmission speeds. 

This display does 

not

 correspond to continuous 

evaluation of the optical power.

Master

T-BUS

D-SUB

FO port A

Slave

Master

T-BUS

D-SUB

FO port A

Slave 1

D-SUB

FO port A

T-BUS

Slave 2

Содержание PSI-MOS-RS232/FO 1300 E


















Отзывы: