Philips TDA1562Q Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 62

background image

Philips Semiconductors

AN<nnnnn>

TDA1562Q application note

<12NC>

© Koninklijke Philips Electronics N.V. 2004. All rights reserved.

Application note

Rev. 01.02 — 05 May 2006

52 of 62

Fig 40. Current distribution between Schottky and parasitic diode

With a ROHM RSX301L schottky diode (3A) it was not possible to damage the amplifier
down to pulse voltages of –30V (which was the limiting value of the test setup used) with
a pulse duration of 50ms. Fig. 4 also shows that the current through the parasitic diode
may exceed 3.5A with a considerable amount, as long as the duration is no more than
50

µ

s.

This setup was tested for 4 hours with a pulse signal with a pulse duration of 50ms and a
duty cycle of 50%. After the test the device was still undamaged.

The conclusion of this test is that a 3A schottky diode should be sufficient to protect the
device against negative voltage pulses.

8.2 Positive voltage pulses at the outputs

Beside negative voltage pulses at the outputs, it is also possible that positive pulses
occur at the outputs.

To check the effect of positive pulses at the outputs, a number of tests was carried out on
the TDA1562.

First of all, test were carried out with the amplifier operating normally with the lift
capacitors charged.

Under these conditions it was only possible to damage the device by applying a DC
voltage higher than 25V to the output.

Iparasitic, 5A/div.

I schottky, 10A/div.

«
...
50
51
52
53
54
...
»

Содержание TDA1562Q































































Отзывы:

Нет отзывов

Похожие инструкции для TDA1562Q

Бренд: Zenith Страницы: 8

Бренд: Fairchild Страницы: 8

Бренд: RAM Страницы: 13

Бренд: Veloce Страницы: 15

Stereo Festival II

Бренд: Harman Kardon Страницы: 16

Бренд: Focal Страницы: 8

Бренд: Adcom Страницы: 1

Бренд: Cary Audio Design Страницы: 14

Бренд: Sansui Страницы: 15

SILVER REFERENCE

Бренд: Trinity Страницы: 22

Бренд: Onkyo Страницы: 9

Бренд: M2TECH Страницы: 37

Бренд: Pyle Pro Страницы: 13

Бренд: Chord Страницы: 4

Бренд: Rockford Fosgate Страницы: 12

Бренд: Custom Valve 50 Страницы: 14

Бренд: Crate Страницы: 4

Бренд: L.R. Baggs Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды