Pfaff 3568-12/12 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 52

Pfaff 3568-12/12 Скачать руководство пользователя страница 40

40

22.8

8 - PLAIN FABRIC

When processing unicoloured material the function of the foot switch is not necessary.

Press key

and numeric keys

and

.

This altered function procedure can be switched on with numeric key

and off with

numeric key

.

22.9

9 - INTERIM STOP

In “AUTOMATIC” mode the function effects a program stop after the conclusion of the folding
procedure for checking purposes and for positioning a label.
The program can be continued by pressing the two start buttons on the loading station.

Press key

and numeric keys

and

.

The intermediate stop can be switched off by pressing numeric key

and on by pressing

numeric key

.

22.10

0 - FURTHER FUNCTIONS

1 - AUTO HEAD LIFT (Lifting the head automatically for bobbin change)

Press key

and numeric keys

and

.

The function can be switched off by pressing numeric key

and on by pressing numeric

key

.

2 - LABEL FEEDER - Automatic label feed- (optional)

Press key

and numeric keys

and

.

The label feed can be switched off by pressing numeric key

and on by pressing numeric

key

.

«
...
38
39
40
41
42
...
»

Содержание 3568-12/12





















































Отзывы:

Нет отзывов