Pfaff 3568-12/12 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 52

Pfaff 3568-12/12 Скачать руководство пользователя страница 34

34

21

6 - TIME ADJUSTMENTS

21.1

1 - TIMING FOR AIR BLAST STACKER

The duration of the air blast must be regulated so that the workpiece to be stacked is blown securely
on top of the stacker stand.

In order to increase or decrease the duration of the air blast press key

and numeric keys

and

.

In the bottom line of the display the following appears:

AIR BLAST ST.

along with the entered value in seconds.

Enter a new value by pressing numeric keys

to

and verify it by pressing the

key.

21.2

2 - TIMING FOR STACKER ROLLER (Running time of stacker roller)

The stacked workpieces must rest in a centered position on top of the stacker stand (fig. 1).

In order to increase or decrease the running time of stacker roller press key

and numeric

keys

and

.

In the bottom line of the display the following appears:

STACKER ROLLER

along with the entered value in seconds.

Enter a new value by pressing numeric keys

to

and verify it by pressing the

key.

«
...
32
33
34
35
36
...
»

Содержание 3568-12/12





















































Отзывы:

Нет отзывов