Pfaff 3568-12/12 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 52

Pfaff 3568-12/12 Скачать руководство пользователя страница 38

38

22

7 - SWITCH FUNCTIONS

22.1

1 - AIR BLAST SELECTION

1 - N. COOLING, TR. FOR.(Needle cooling during forward transfer)

In order to prevent the starting thread from being pushed underneath the presser foot during
the workpiece transfer.

Press key

and numeric keys

and then

again.

The air blast can be switched on with numeric key

and off with numeric key

.

2 - N. COOLING STACKER (Needle cooling whilst stacking)
- if desired -

Press key

and numeric keys

and

.

The air blast can be switched on with numeric key

and off with numeric key

.

Air blast “workpiece transfer aid”

(optional)

When processing large workpieces it is possible to work with the air blast “workpiece transfer aid”
during the function procedures “jig feed forwards”, “stacking”, and “sewing” in order to prevent the
workpieces from jamming.

3 - FAB. FEED, TR. FORW. (Air blast whilst “forward transfer”)

Press key

and numeric keys

and

.

The air blast can be switched on with numeric key

and off with numeric key

.

4 - FAB. FEED STACKER (Air blast whilst “stacking”)

Press key

and numeric keys

and

.

The air blast can be switched on with numeric key

and off with numeric key

.

5 - FAB. FEED SEWING (Air blast whilst sewing)

Press key

and numeric keys

and

.

The air blast can be switched on with numeric key

and off with numeric key

.

«
...
36
37
38
39
40
...
»

Содержание 3568-12/12





















































Отзывы:

Нет отзывов