3
M73 TL VULCAN TRIACT-LOCK M735200C (220610)
(EN) ENGLISH
Only the techniques shown in the diagrams that are not crossed
out and/or do not display a skull and crossbones symbol are
authorized. Check our Web site regularly to find the latest
versions of these documents: www.petzl.com
Contact PETZL if you have any doubt or difficulty understanding
these documents.
VULCAN TRIACT-LOCK
Double autolocking steel carabiner
- Connector EN 362: 2004 classe B
- NFPA 1983 General use
Field of application
This equipment is personal protective equipment (PPE) used
for fall protection.
This carabiner is used to connect equipment together during
rescue or work at height activities.
This product must not be loaded beyond its strength rating,
nor be used for any purpose other than that for which it is
designed.
WARNING
Activities involving the use of this equipment are inherently
dangerous.
You are responsible for your own actions and decisions.
Before using this equipment, you must:
- Read and understand all instructions for use.
- Get specific training in its proper use.
- Become acquainted with its capabilities and limitations.
- Understand and accept the risks involved.
Failure to heed any of these warnings may result in severe
injury or death.
Responsibility
WARNING, specific training in the activities defined in the field
of application is essential before use.
This product must only be used by competent and responsible
persons, or those placed under the direct and visual control of
a competent and responsible person.
Gaining an adequate apprenticeship in appropriate techniques
and methods of protection is your own responsibility.
You personally assume all risks and responsibilities for all
damage, injury or death which may occur during or following
incorrect use of our products in any manner whatsoever. If you
are not able, or not in a position to assume this responsibility
or to take this risk, do not use this equipment.
Nomenclature of parts
(1) Frame, (2) Gate, (3) Hinge, (4) Locking sleeve, (5) Keylock,
(6) Keylock slot.
Principal materials: steel.
Inspection, points to verify
Before each use
Verify that the frame, hinge and locking sleeve are free of any
cracks, deformation, corrosion, etc.
Open the gate and verify that it closes and locks itself
automatically when released. The Keylock slot must not be
blocked by any foreign matter (dirt, pebble, etc.).
During each use
It is important to regularly inspect the condition of the product.
Make sure that all pieces of equipment are properly connected
and positioned with respect to each other.
Consult the details of the inspection procedure to be carried out
for each item of PPE on the Web at www.petzl.com/ppe or on
the PETZL PPE CD-ROM.
Compatibility
A connector must be compatible with the equipment to which it
is attached (shape, size, etc.).
An incompatible connection can affect the safety function of the
system (for example, disconnection, breakage, etc.).
WARNING if the connector is attached to an element of
the system that is too large (for example wide slings, large
bars, etc.) the connector’s strength can be reduced.
Working principle
Diagram 1. Manipulation
Diagram 2. Installation of the carabiner
This connector must always be used with the gate closed and
locked.
The strength of the connector is greatly reduced if the gate is
open. Systematically check that the gate is securely locked.
Lock it manually if necessary. Contaminants such as mud,
sand, paint, ice, dirty water, etc. can prevent the automatic
locking system from working.
The carabiner is strongest when closed and loaded on its major
axis. Any other position reduces its strength.
Diagram 3. Warning danger of death
Any external pressure on the gate (with a descender, for
example) is dangerous. When a sudden tension comes onto the
rope, the locking sleeve can break and the gate can open itself.
The device or rope may detach itself from the connector.
Remember: For your safety, get into the habit of always
doubling-up your systems, especially carabiners.
Supplementary information
regarding standards (EN 365)
Rescue plan
You must have a rescue plan and the means to rapidly
implement it in case of difficulties encountered while using this
equipment.
Anchors
The anchor point for the system should preferably be located
above the user’s position and should meet the requirements of
the EN 795 standard (minimum strength of 10 kN).
Clearance: amount of free space below the user
The clearance below the user must be sufficient to prevent the
user from striking any obstacle in case of a fall. (The length of
the connector can influence the height of a fall).
Various
- Take care to minimize the potential for falls and the height of
any potential fall.
- WARNING, take care that your products do not rub against
abrasive or sharp surfaces.
- When using multiple pieces of equipment together, a
dangerous situation can result if the safety function of one
piece of equipment is affected by the safety function of another
piece of equipment.
- Users must be medically fit for activities at height.
- You must verify the suitability of this equipment for use
in your application with regard to applicable governmental
regulations and other standards on occupational safety.
- The instructions for use for each item of equipment used in
conjunction with this product must be respected.
- The instructions for use must be provided to users of this
equipment in the language of the country in which the product
is to be used.
Petzl general information
Lifetime / When to retire your equipment
For Petzl plastic and textile products, the maximum lifetime
is 10 years from the date of manufacture. It is indefinite for
metallic products.
ATTENTION: an exceptional event can lead you to retire a
product after only one use, depending on the type and intensity
of usage and the environment of usage (harsh environments,
sea, sharp edges, extreme temperatures, chemical
products, etc.).
A product must be retired when:
- It is over 10 years old and made of plastic or textiles.
- It has been subjected to a major fall (or load).
- It fails to pass inspection. You have any doubt as to its
reliability.
- You do not know its full usage history.
- When it becomes obsolete due to changes in legislation,
standards, technique or incompatibility with other
equipment, etc.
Destroy retired equipment to prevent further use.
Product inspection
In addition to the inspection before each use, an in-depth
inspection must be carried out by a competent inspector. The
frequency of the in-depth inspection must be governed by
applicable legislation, and the type and the intensity of use.
Petzl recommends an inspection at least once every 12 months.
To help maintain product traceability, do not remove any
markings or labels.
Inspection results should be recorded on a form with the
following details: type of equipment, model, manufacturer
contact information, serial or individual number; dates
of: manufacture, purchase, first use, next periodic inspection;
notes: problems, comments; name and signature of the
inspector.
See an example at www.petzl.fr/ppe or on the Petzl PPE CD-
ROM.
Storage, transport
Store the product in a dry place away from exposure to UV,
chemicals, extreme temperatures, etc. Clean and dry the
product if necessary.
Modifications, repairs
Modifications and repairs outside of Petzl facilities are
prohibited (except replacement parts).
3-year guarantee
Against all material or manufacturing defect. Exclusions: normal
wear and tear, oxidation, modifications or alterations, incorrect
storage, poor maintenance, negligence, uses for which this
product is not designed.
Responsibility
PETZL is not responsible for the consequences, direct, indirect
or accidental, or any other type of damage befalling or resulting
from the use of its products.
Traceability and markings
a. Body controlling the manufacture of this PPE
b. Notified body that carried out the CE type inspection
c. Traceability: datamatrix = product ref individual
number
d. Diameter
e. Individual number
f. Year of manufacture
g. Day of manufacture
h. Control or name of inspector
i. Incrementation
