Perle RPS1620 Скачать руководство пользователя страница 40

Страница: 40 / 72

5-16

RPS Series: Remote Power Switches - User's Guide

5.3.4. Network Parameters Menus

The Network Parameters Menus are used to select the IP Address and other

network parameters.

•

Web Browser Interface:

Click the "Setup" button to access the Setup

Menus, and then click the "Network Parameters" button. The Web

Parameters Menu will be displayed as shown in Figure 5.9.

•

Text Interface:

Type

and press

[Enter]

. The Network Parameters

Menu will be displayed as shown in Figure 5.10.

Notes:

• Although the Web Browser Interface and Text Interface both

allow conﬁguration of the same network parameters, note that

for the Text Interface, the IP Security feature is conﬁgured via a

separate submenu. For more information on IP Security, please

refer to Section 5.3.4.1.

• Settings for network parameters depend on the conﬁguration of

your individual network. Contact your network administrator

for appropriate settings.

The Network Parameters Menu allows the following parameters to be deﬁned.

Except where noted, all parameters listed here are available via both the Web

Browser Interface and the Text Interface.

•

IP Address:

Deﬁnes the IP address for the RPS unit.

(Default = 192.168.168.168.)

•

Subnet Mask:

Deﬁnes the Subnet Mask for the RPS unit.

(Default = 255.255.255.0.)

•

Gateway Address:

Deﬁnes the Gateway Address for the RPS unit.

(Default = undeﬁned.)

•

Send MSS:

Deﬁnes the Maximum Segment Size that will be sent by the

RPS. (Default = 536.)

•

IP Security:

Please refer to Section 5.3.4.1 for a detailed description of

the IP Security feature.

•

MAC Address:

Displays the unit’s MAC Address. Please note that this

item only displays the assigned MAC Address, and cannot be used to

redeﬁne the address.

Notes:

• To display the Network Status Screen, type

/SN

and press

[Enter]

• To reset the Network Port, type

and press

[Enter]

Содержание RPS1620









































































Результаты поиска

Содержание RPS1620

Отзывы:

Похожие инструкции для RPS1620

Бренды по названию

Популярные бренды

Perle RPS1620, Руководство пользователя

Результаты поиска

Содержание RPS1620

Отзывы:

Похожие инструкции для RPS1620

Бренды по названию

Популярные бренды