Perle RPS1620 Скачать руководство пользователя страница 27

Страница: 27 / 72

5-3

Conﬁ guration

5.2.1. Accessing the Web Browser Interface

In order to issue commands via the Web Browser Interface, the RPS must

be connected to a TCP/IP network, and your PC must be equipped with a

JavaScript enabled web browser (such as Internet Explorer™ or

Netscape™ Navigator.)

1. Start your JavaScript enabled Web Browser.
2. Key the RPS’s IP address (default = http://192.168.168.168) into the

web browser’s address bar, and then press

[Enter]

Password Prompt:

The RPS will display a prompt, which asks for

your name and password.
a)

User Name:

If you have not previously deﬁned a user name, then

this ﬁeld should be left blank. A user name is only required when

one has been deﬁned via the General Parameters menu.

Password:

Key in your System Password or Plug Password and

then click "OK" (Note that Plug Passwords do not permit access to

conﬁguration functions.)

c) If the System Password has

not

been deﬁned, simply click the "OK"

button without keying in a name or password.

If a valid password is entered, the Plug Status Screen (Figure 5.1) will appear.

Содержание RPS1620









































































Результаты поиска

Содержание RPS1620

Отзывы:

Похожие инструкции для RPS1620

Бренды по названию

Популярные бренды

Perle RPS1620, Руководство пользователя

Результаты поиска

Содержание RPS1620

Отзывы:

Похожие инструкции для RPS1620

Бренды по названию

Популярные бренды