Perle RPS1620 Скачать руководство пользователя страница 59

Страница: 59 / 72

8-1

8. Upgrading the RPS Firmware

When new, improved versions of the RPS ﬁrmware become available, the

"Upgrade Firmware" function can be used to update the unit. Updates can be

installed via the Console Port or Network Port.

Notes:

• The upgrade procedure can only be performed via the Text

Interface.

• All other network ports will be disabled during the ﬁrmware

upgrade procedure.

• When the upgrade procedure is complete, all parameters will be

set to their default states. Therefore, it is recommended to save

RPS conﬁguration parameters to an ASCII ﬁle (as described in

Section 7) before beginning this upgrade procedure.

1. Obtain the update ﬁle. Firmware modiﬁcations can either be mailed to

the customer on a CDR, or downloaded. Place the upgrade CDR in your

disk drive or copy the ﬁle to your hard drive.

2. Access the RPS command mode via the Text Interface. When the

password prompt is displayed, key in the System Level Password.

3. When the command prompt appears, type

and press

[Enter]

. The

RPS will display a screen which offers the following options:
•  1. Upgrade Sector 0
•  2. Upgrade Sectors 1 - 4
•  3. Upgrade Sectors 5 - 7
•  4. Abort Upgrade

Note:

Instructions regarding the proper Sector option will be

supplied when upgrades become available.

Select the Sector Option indicated for the upgrade and press

[Enter]

, or

type

[Enter]

to abort the upgrade procedure.

Содержание RPS1620









































































Результаты поиска

Содержание RPS1620

Отзывы:

Похожие инструкции для RPS1620

Бренды по названию

Популярные бренды

Perle RPS1620, Руководство пользователя

Результаты поиска

Содержание RPS1620

Отзывы:

Похожие инструкции для RPS1620

Бренды по названию

Популярные бренды