manualshive.com logo in svg

Pergola kits USA WOOD GABLE ROOF PAVILION, Инструкция по сборке, Страница: 18 / 24

Поделиться
Скачать
Pergola kits USA WOOD GABLE ROOF PAVILION Скачать руководство пользователя страница 18

18

Roofing Option 2:

Installing An Asphalt Roof

NOTE: Before you begin the steps below, install roof paper starting at the bottom. Be sure to overlap 2" as 

you work upward. Drip edge will then be installed on all edges of the roof, using a fastener every 16".

Roofing Fasteners

Please note we do not include fasteners for asphalt shingles with our kits. This is because some states 

require different fasteners than others, and because some customers have different tools than others 

(hammer, nail gun, pneumatic stapler, hammer tacker, etc.).

Please use shallow depth fasteners to fasten your shingles to your 1x6 roof decking. For example:

•  5/8” long roofing nails

•  Roofing staples with 5/8” leg and 1” wide crown

These fasteners will certainly be sufficient to hold the shingles to your roof in high storm winds, and will 

not pierce the bottom surface of the 1x6 roof decking.

DO NOT PLACE PLYWOOD, OSB (ORIENTED STRAND BOARD) OR OTHER 

DECKING ON TOP OF THE 1X6 TONGUE AND GROOVE.

It is not necessary and is too heavy for your structure.

1

To install 1st row of shingles, 

turn shingle upside down 

with black tar line at bottom 

edge facing up and attach to 

roof  using  four  5/8”  roofing 

nails. Place nails approximately 

3” from bottom.

Содержание WOOD GABLE ROOF PAVILION

























Отзывы:

Нет отзывов