Pepperl+Fuchs IMUF99 B20 Series Скачать руководство пользователя страница 12

Страница: 12 / 53

Inertial Measurement Unit IMUF99*B20

Installation

Installation

3.1

Electrical connection

The IMU360D-F99 is equipped with 2 connectors M12 x 1, 5-pin, male and female for CAN bus

integration. If a terminator is required, it muss be attached externally on the female connector.

Therefore e. g. "Terminator ICZ-TR-CAN/DN-V15" from Fuchs is available (also see

datasheet of the sensor).

Connecting the sensor to the voltage

Connect the operating voltage to pins 2 and 3 of the 5-pin connector.

The "Power" LED lights up green.

Pin

Wire color

Designation

Brown

Not used

White

+UB

Blue

GND

Black

CAN-H

Gray

CAN-L

Table 3.1

Connector assignment

n.c.

2
3

+UB
GND

CAN-L

4
5

CAN-H

Note

The wire colors listed above apply when one of the bus cables from the Fuchs

accessories range is used.

Note

The device complies with the EMC norms and standards described in the datasheets. If

necessary, additional external EMC protection elements and interference suppression

measures (e.g. filters) are recommended.

Warning!

Damage to the device
Connecting an alternating current or excessive supply voltage can damage the device or cause

the device to malfunction.
Electrical connections with reversed polarity can damage the device or cause the device to

malfunction.
Connect the sensor to direct current (DC). Ensure that the supply voltage rating is within the

specified sensor range. Ensure that the connecting wires on the cordset in use are connected

correctly.

Содержание IMUF99 B20 Series






















































Результаты поиска

Содержание IMUF99 B20 Series

Отзывы:

Похожие инструкции для IMUF99 B20 Series

Бренды по названию

Популярные бренды

Pepperl+Fuchs IMUF99 B20 Series, Руководство пользователя

Результаты поиска

Содержание IMUF99 B20 Series

Отзывы:

Похожие инструкции для IMUF99 B20 Series

Бренды по названию

Популярные бренды