manualshive.com logo in svg

Pepperl+Fuchs IMUF99 B20 Series, Руководство пользователя, Страница: 10 / 53

Поделиться
Скачать
Pepperl+Fuchs IMUF99 B20 Series Скачать руководство пользователя страница 10

 2

02

2-

06

10

Inertial Measurement Unit IMUF99*B20

Product Description

Selectable output values and filters

Several selectable output values such as acceleration, rotational speed, inclination (Euler 

angle, Euler value, quaternions) and programmable filters allow you to perfectly adapt the mea

-

suring system to your application.
Parameterization and data transfer take place via the integrated CAN SAE J1939 interface.
In the following figure the signal path of input and output values is illustrated.

Figure 2.5

Triple Axis 

Accelerometer

Triple Axis 

Gyroscope

Filter 0

Filter 1

Filter 2

Filter 5

Filter 4

Sensor Fusion 

Algorithm

Acceleration (Acc)

Mapping ID 0-2

Rotation Rate (Gyro)

Mapping ID 3-5

Rotational Acceleration (RotAcc)

Mapping ID 6-8

Gravity Vector (Grav)

Mapping ID 12-14

Linear Acceleration (LinAcc)

Mapping ID 15-17

Euler Angles (EUI) /
P +F Angles INX/INY

Mapping ID 18-20

Quaternion (Quat)

Mapping ID 21-24

Temperature 

Elements

Temperature (Temp)

Mapping ID 25-26

F(x)

F(x)

•

 P+F Angles INX / INY

F(x)

• 

Quaternion

• 

Euler Angles

F(x)

Sensor
Elements

Output
Data

Software

Содержание IMUF99 B20 Series






















































Отзывы:

Нет отзывов