General Safety Information
2
Description
Myers Drainer Pre-Plumbed System, Model Number
ED33V1, is ideal for home wastewater removal from
beautician or utility sinks and wet bars, and for drain
water transfer from air conditioners or dehumidifiers.
1/3 HP submersible pump unit is equipped with a 3-prong
grounding-type power cord. Motor is oil-filled (dielectric
oil) and sealed for cooler running. Upper sleeve/lower
ballbearing on motor shaft never need lubrication.
Automatic reset thermal protection.
specifications
Power supply required ..................................115V, 60 Hz.
Liquid temp. range ......................................... 32° to 130°F
Individual branch circuit required (minimum) ..... 15 Amps
Discharge .......................................................... 1-1⁄2" NPT
Unpacking anD inspection
Handle with care. Check items received against packing
list to be sure that all equipment has been received.
Inspect for shipping damage. If found, file claim with
carrier immediately.
general safety information
Electrically powered sump pumps normally give many
years of trouble-free service when correctly installed,
maintained, and used. However, unusual circumstances
(interruption of power to the pump, dirt/debris in the
sump, flooding that exceeds the pump’s capacity,
electrical or mechanical failure in the pump, etc.) may
prevent the pump from functioning normally. To prevent
possible water damage due to flooding, consult your
dealer about installing a high water alarm. See the
“Troubleshooting Chart” in this manual for information
about common sump pump problems and remedies.
For more information, see your dealer or call customer
service.
1. Know the pump application, limitations, and potential
hazards.
2. Disconnect power before servicing.
3. Release all pressure within system before servicing any
component.
4. Drain all water from system before servicing.
5. Secure discharge line before starting pump. An
unsecured discharge line will whip, possibly causing
personal injury and/or property damage.
6. Check hoses for weak or worn condition before each
use, making certain that all connections are secure.
7. Periodically inspect system components. Keep
free of debris and foreign objects. Perform routine
maintenance as required.
8. Provide means of pressure relief for pumps whose
discharge line can be shut-off or obstructed.
9. Personal Safety:
a. Wear safety glasses at all times when working with
pumps.
b. Keep work area clean, uncluttered and properly
lighted – replace all unused tools and equipment.
c. Keep visitors at a safe distance from work area.
d. Make workshop child-proof – with padlocks,
master switches, and by removing starter keys.
10. When wiring an electrically driven pump, follow all
electrical and safety codes that apply.
11. This equipment is only for use on 115 volt (single
phase) and is equipped with an approved
3-conductor cord and 3-prong, grounding-type plug.
to reduce risk of electric shock, pull plug
before servicing.
This pump has not been investigated
for use in swimming pool areas. Pump is supplied with
a grounding conductor and grounding-type attachment
plug. Be sure it is connected only to a properly grounded
grounding-type receptacle. Where a 2-prong wall
receptacle is encountered, it must be replaced with
a properly grounded 3-prong receptacle installed in
accordance with codes and ordinances that apply.
12. All wiring should be performed by a qualified
electrician.
13. Make certain power source conforms to requirements
of your equipment.
14. Protect electrical cord from sharp objects, hot surfaces,
oil, and chemicals. Avoid kinking cord. Replace or
repair damaged or worn cords immediately.
15. Do not touch an operating motor. Modern motors are
designed to operate at high temperatures.
performance
specifications
gpm of Water @ total feet of Head
model
Hp
5’
10’
15’
20’
shutoff
eD33V1
1/3 48.0 40.0 29.0 15.0 24’
motor
full load
switch setting
top
Bottom
Hp
amps
on
off
Height
Width
Width
Weight
1/3
9.8
7"
2"
13-3/4"
15-1/8"
12"
32 lbs.
