Pentair EASYTOUCH PL4 Скачать руководство пользователя страница 44

Страница: 44 / 80

EASYTOUCH

PL4/PSL4 Control Systems User’s Guide

INTELLIFLO VS SPEEDS SETTING:

Down button:

Choose

Speeds

Right button:

Access the IntelliFlo VS speed (RPM) settings

for Pump #1.

Up/Down button:

Select the

circuit number 1 of 4

(1/4).

Right button:

Move to

RPM

to change the pump speed.

Up/Down buttons:

Set speed of the pump from 400 to 3450 RPM in increments of

10 RPM. The default speed for each circuit correspond to the four speed buttons on
the IntelliFlo VS control panel is:

Speed 1 button 750 RPM, Speed 2 button 1500

RPM, Speed 3 button 2350 RPM, and Speed 4 button 3110 RPM.

INTELLIFLO VSF+SVRS FLOW RATE SETTING:

Down button:

Choose

Flow/Speeds

Right button:

Access the IntelliFlo VSF+SVRS speed (RPM/GPM) settings

for Pump

#1.

Up/Down button:

Select the

circuit number 1 of 4

(1/4).

Right button:

Move to

GPM

to change the pump flow rate.

Up/Down button:

Select

RPM or GPM

. Press

Up/Down button

to toggle between

RPM and GPM and pressure setting (PSI).

Right button (GPM):

Move to

GPM

pump flow rate.

Up/Down button:

Set speed of the pump from 15 to 130 GPM. The default flow

rate is 30 GPM. The preset speed for each button is:

Speed 1 button 1100 RPM

(30 GPM), Speed 2 button 1500 RPM, Speed 3 button 2350 RPM, and Speed 4
button 3110 RPM.

Right button (GPM/PSI):

Move to

PSI

(pounds per square inch) pressure setting.

Up/Down button:

Select the pump pressure setting from 1 to 30 PSI.

See above for

equivalent default RPM/GPM (speed/flow rate).

VS and VSF+SVRS CIRCUIT SETTING:

Right button:

Move to the circuit names.

Up/Down buttons: Assign the pump circuit:

NONE, SPA, POOL, AUX 1-3,

FEATURE 1-2, HEATER, POOL HEATER, SPA HEATER, FREEZE, POOL/SPA, and
SOLAR/HEAT.

Right button:

Press the

Up arrow button

and go to the next circuit page settings

(2/4) and repeat the previous steps.
When finished setting up the circuits, press the

Menu

button to save the settings and

to return to the Settings menu options. Press the button two times to return to the
main screen.

INTELLIFLO VS STATUS SETTING:

Down button:

Choose

STATUS

Right button:

View the current IntelliFlo VS pump status.

Menu:

Press

MENU

to exit.

IntelliFlo VS and VSF+SVRS Settings (Continued)





Pump #1 Type

Type: VS

Pump #1 1/4

RPM: 1200

Circuit:

[ POOL ]



Pump #1 1/4

GPM:30 PSI: 15

Circuit:

[ NONE ]



Pump Type

Flow/Speeds

Status







Pump #1 Type

Type: VSF+SVRS





Pump #1 1/4

GPM:30 PSI: 15

Circuit:

[ AUX 1 ]



GPM: 30

1200 RPM 12 W

Watts: 10

Status: GOOD



Содержание EASYTOUCH PL4

















































































Результаты поиска

Содержание EASYTOUCH PL4

Отзывы:

Бренды по названию

Популярные бренды

Pentair EASYTOUCH PL4, Руководство пользователя

Результаты поиска

Содержание EASYTOUCH PL4

Отзывы:

Бренды по названию

Популярные бренды