background image

10

Useful Information

The diameter of the tubing which will be connected to the gas outlets is important and 

is  determined  by  the  length  of  tubing  required.    Failure  to  follow  these 

recommendations could lead to accelerated compressor wear.

< 10 meters.

Use 6/4 (6mm O/D, 4mm I/D) P.T.F.E. tubing. 

> 10 - 40 meters. 

Use 10/8 (10mm O/D, 8mm I/D).

> 40 metres. 

Please contact Peak with the relevant distance and we will 

calculate the flow resistance and the tubing size required.

A combination of 6/4 and 10/8 tubing may be used to ensure that there is no large 

diameter tubing within the lab (i.e. for the first 10 meters use 6/4 tubing and the final 

20 meters use 10/8). 

Keep the connections and bends to a minimum.

The imperial equivalents are:-

6/4 = 1/4” O/D, 3/16” I/D.

10/8= 3/8” O/D, 5/16” I/D.

Electrical Connection

Important Electrical Notice

This  unit  is  classified  as  SAFETY  CLASS  1 equipment.    THIS  UNIT  MUST  BE 

EARTHED.    Before  connecting  the  unit  to  the  mains  supply,  please  check  the 

information on the serial plate.  The mains supply must be of the stated AC voltage 

and frequency.

The Electrical requirement is:-

230V AC (50/60 Hz), 8.4 Amps

EARTH/GROUND (E):-

Green & Yellow 

or

Green

LIVE (L):-

Brown

or

Black

Neutral (N):-

Blue

or

White

Connect the compressor to a single-phase supply using the power cord provided.

Installation

Nitrogen N*10DR Nitrogen Generator

UM  – N*10DR – Rev 4

Содержание N 10DR Series


















Отзывы: