background image

 

   

          

-15 -       

PATON

 StandardMIG

 MMA/TIG/MIG/MAG

 

drop  transfer  into  the  weld  pool  and,  consequently,  on  the  stability  of  the  weld 
forming  and  of  the  welding  process.  In  other  words,  this  process  substitutes 
movements  of  welder’s  hand  to  some  extent,  which  is  especially  important  in 
hard‐to‐reach places. The correct setting determines weld shape and quality of the 
weld  forming,  thus  reducing  risk  of  porosity  and  grain  structure  of  the  weld  and 
consequently increasing weld strength. 

In  order  to  implement  this  function,  three  parameters  must  be  set  in  the 

machine:  pulsing  power  [Po.P],  pulsing  frequency  [Fr.P]  and  mark‐to‐space  ratio 
(or duty ratio) [dut]. By default, pulsing power [Po.P], which is the key parameter, 
is set to “OFF” position, i.e. disabled, while pulsing frequency [Fr.P] and duty ratio 
[dut] are set to the most common values of 50Hz and 50% respectively. In order to 
enable this function, it is enough to set pulsing power [Po.P] to a value above zero. 
This parameter is set in percent of the current set value of base arc welding. 

Example: welding with a Ф3mm electrode, set the base value of arc current is 

60 A, and pulsing power [Po.P] = 40%, while pulsing frequency [Fr.P] = 5.0Hz and 
duty ratio [dut] = 50% by default. 

Result:  current  will  pulse  in  the  range  from  36A  to  84A  with  a  frequency  of 

5Hz; pulses will be of the same shape in terms of both magnitude and time. If duty 
ratio  parameter  [dut]  is  changed  to  a  value  other  than  50%,  pulses  become 
asymmetric—between the current pulse time and the current “pause” time: 

by default 

“duty ratio” [dut] = 50% 

“duty ratio” [dut] = 20% 

“duty ratio” [dut] = 70% 

 

 

The  machine  calculates  pulsing  in  such  a  way  that,  at  a  constant  set 

differential of pulses, average level of welding current is maintained at the level of 
set base welding current value of 60A (i.e. equal to the set value), in order to keep 
the resulting average heat input into the weld at a constant level of 60A, but the 
stability of the welding process and the mixing of the weld pool will change. This is 
necessary  in  the  situation,  when  a  user  has  reduced  base  current  and  provided 
maintenance of stable welding process using pulses—thus, decrease of heat input 
can also be clearly determined by comparison with initial base current. 

These  parameters  are  set  differently  in  different  situations  in  accordance 

with welding operator’s requirements. See Clause 6.1 for sequence of changing the 
value of any function in the current welding mode. 

 

t, s 

t, s 

t, s 

Содержание StandardMIG-160






































Отзывы: