background image

 

PATON

 StandardMIG

 MMA/TIG/MIG/MAG                     

-10 -

 

ATTENTION!  When  the  machine  is  switched  off  and  cools  down  after  an 

operation  in  cold  season,  condensate  forms  inside  of  it,  so  do  not  switch  the 
machine on again in less than 3...4 hours!!! 

Therefore,  do  not  switch  the  machine  off  in  cold  season,  if  you  are  going  to 

switch it on within 4 hours. 

The  machine  must  be  placed  to  ensure  free  inlet  and  outlet  of  cooling  air 

through the vent holes on the front and the rear panels. Take care that metal dust 
(for example, during emery grinding) does inhaust directly into the machine by the 
cooling fan. 

ATTENTION!  The  machine  may  be  life‐threatening  after  a  hard  fall.  So 

place it on a stable, solid surface. 

 

2.3 POWER CONNECTION 

The  welding  machine  of  series  design  is  rated  for  mains  voltage  of  220V  (-

27%+18%) or for three‐phase mains voltage of 3х380V (

±

20%). 

Attention!  All  manufacturer’s  warranty  liabilities  become  void  if  the 

single‐phase  machine  is  connected  to  mains  voltage  exceeding  270V!

 

Such  a 

situation  can  occur  with  a  very  large  phase  voltage  imbalance  in  a  standard 
mains or using non-standard connection. 

In  addition,  manufacturer’s  warranty  liabilities  become  void  if  the  mains 

line  has  been  connected  by  mistake  to  the  neutral  wire  or  to  the  source 
earthing wire during connection of a three‐phase machine. 

Mains connector, cross‐sections of power supply cables, and supply‐line fuses 

must be selected on the basis of technical specifications of the machine. 
 

2.4 MAINS PLUG CONNECTION 

Mains plug shall correspond to supply voltage and current consumption of the 

welding  machine  (see  Technical  specifications).  In  accordance  with  safety 
practices,  use  a sockets  with  a 

guaranteed

  earthing  and  in  no  case 

do not use

 a 

neutral wire for these purposes!!!

 

ATTENTION!

  The  power  switch 

14

  is  a  signal  button  that  blocks  only  the 

power  current  of  the  welding  machine,  but  does  not  completely  de-energize  the 
internal  electronics  of  the  device.  Therefore,  according  to  safety  precautions,  do 
not forget to remove the plug from the socket when reconnecting. 
 

Содержание StandardMIG-160






































Отзывы: