Paton StandardMIG-160 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 37

background image

PATON

StandardMIG

MMA/TIG/MIG/MAG

-30 -

In order to ensure trouble‐free operation:

Output voltage of the generator shall

not fall beyond the permissible range of 160~260V; these are permitted values for
each phase, if a three‐phase machine is used.

9. ATTENDANCE AND TECHNICAL MAINTENANCE

Attention!

Before opening the machine, switch it off and disconnect the mains

plug. Wait until internal circuits of the machine de‐energize (about 5 minutes), and
only then proceed with other actions. When leaving the machine, install a
restrictive plate which prohibits switching the machine on.

In order to ensure proper operation of the machine for many years, adhere to

several rules:

-

conduct inspection in accordance with safety practices within the established
time intervals (see “Safety rules” chapter);

-

if the machine is subject to heavy use, it is recommended to purge it with dry
compressed air once per six months.

Attention!

If the machine is purged from

a very short distance, electronic components may be damaged;

-

if the machine is very dust‐laden, clean channels of the cooling system
manually.

10. STORAGE RULES

A preserved and packaged source shall be stored in storage conditions 4 as per

GOST 15150‐69 for 5 years.

A de‐preserved source shall be stored in dry closed rooms at air temperature

not lower than plus 5°С. The rooms must be free from acid vapours and other
active substances.

11. TRANSPORTATION

A packaged source can be transported by any mode of transport, which

provides its integrity, complying with all transportation rules established for this
mode of transport.

12. TECHNICAL SPECIFICATIONS

Attention!

If a source is designed for special supply voltage, its technical

specifications are provided on the identification plate on the rear panel. In this
case, mains plug and mains cable shall be selected according to the voltage used.

«
...
28
29
30
31
32
...
»

Содержание StandardMIG-160






































Отзывы:

Нет отзывов

Похожие инструкции для StandardMIG-160

Бренд: G-Tek Страницы: 28

Бренд: Magnavox Страницы: 26

Бренд: Eaton Страницы: 12

Бренд: Fbt Страницы: 16

Бренд: FBII Страницы: 83

Бренд: Fbt Страницы: 36

Бренд: FBII Страницы: 10

Бренд: Gateway Страницы: 8

Бренд: Oakley Sound Страницы: 15

Бренд: Oasis Страницы: 18

Megavox Pro MEGA-6000U1

Бренд: Anchor Страницы: 1

Бренд: JBL Страницы: 4

Бренд: Parweld Страницы: 16

Бренд: ZOpid Страницы: 5

Бренд: Lincoln Electric Страницы: 39

Бренд: Dahua Technology Страницы: 15

Бренд: hawa Страницы: 29

Бренд: KITO Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды